EnGenius DuraFon - Regulatory Information; Radiation Exposure Statements; Industry Canada Statements

hellospoke.com 888 / 955 / 5155 EnGenius DuraFon
Basic Call Handling
RECEIVING AN INTERCOM CALL
ENDING A CALL
ADJUSTING HANDSET RECEIVER (EARPIECE) VOICE VOLUME
ADJUSTING HANDSET SPEAKERPHONE VOICE VOLUME
PLACING A CALL ON HOLD
1. When an intercom call arrives (called from other handsets, ex. Handset 12), the ringer will ring or
vibrate unless the ringer has been turned off. Press TALK to answer the intercom call.
2. If the handset is on the charger cradle (ringer will be temporarily switched to “Ring” if it has been set
to “Vibrate”), lift the handset and press the TALK key to start a conversation.
3. If the handset is not on the cradle and MENU-5-2 “Any Key Talk” setting is “On,” press any key (ex-
cept END and the SILENT soft key) to answer.
NOTES:
1. The LCD displays the caller’s Handset ID.
2. You can press the SILENT (Left) soft key if you choose to ignore the call. Unlike turning off the ringer
the SILENT key operation is valid only for the current call.
To end a telephone or intercom call, press the END key, or place handset into charger cradle.
1. Voice volume can only be adjusted during a call.
2. There are 6 levels of volume selections. Use the UP or DOWN keys to adjust.
3. The new setting will remain effective for all future calls until changed.
1. Voice volume can only be adjusted during a call (in speakerphone mode).
2. There are 6 levels of volume selections. Use the UP or DOWN keys to adjust.
3. The new setting will remain effective for all future calls until changed.
1. When a call is in progress, it can be put on hold by pressing OPTION (Right) soft key and the
*
key.
2. To return to the conversation, press UNHOLD (Left) soft key.
NOTES:
1. Handset LCD displays when a call is on hold. An alert tone (a beep) every 30-seconds will remind the
handset that a call is on hold.
2. If the operation (e.g., call transfer) fails after putting a call on-hold, the held call may be dropped.
~32~
Receiving a Telephone Call
1.
When an incoming call arrives, the LCD will show the Caller
ID message, and the ringer will ring or vibrate unless the
ringer has been turned off.
Joe
033289289
SILENT
11
1
L1
2.
If the handset is on the charger cradle (ringer will be
temporarily switched to “Ring” if it has been set to
“Vibrate”), lift the handset and press key to start a
conversation.
Re:
You can turn on the “Any Key Talk” from MENU-5-2.
Notes:
1. You can press SILENT (Left) soft key if you choose to ignore the call.
Unlike turning off the ringer (from the handset menu), the SILENT
key operation is valid only for the current call.
2. If Caller ID service is available, the LCD will display the incoming call
information. If the LCD shows “Private” or “Unknown,” the caller or
the originating phone company may have blocked the caller’s
information.
Receiving an Intercom Call
1.
When an intercom call arrives (called from other handsets,
ex. Handset 12), the ringer will ring or vibrate unless the
ringer has been turned off. Press to answer the
intercom call.
Incoming page
from Ext #12
SILENT
11
L
1
2.
If the handset is on the charger cradle (ringer will be
temporarily switched to “Ring” if it has been set to
“Vibrate”), lift the handset and press key to start a
conversation.
~33~
3.
If the handset is not on the cradle and MENU-5-2 “Any Key Talk” setting is “On,”
press any key (except and the SILENT soft key) to answer.
Notes:
1. The LCD displays the caller’s Handset ID.
2. You can press the SILENT (Left) soft key if you choose to ignore the call.
Unlike turning off the ringer the SILENT key operation is valid only for
the current call.
Ending a Call
To end a telephone or intercom call, press key, or place handset into charger
cradle.
Adjusting Handset Receiver (Earpiece) Voice Volume
1.
Voice volume can only be adjusted during a call.
00:00:15
Volume: 3
11
MUTE OPTION
L
1
2.
There are 6 levels of volume selections. Use or
key to adjust.
3.
The new setting will remain effective for all future calls
until changed.
Adjusting Handset Speakerphone Voice Volume
1.
Voice volume can only be adjusted during a call (in
speakerphone mode).
00:00:15
Volume: 3
11
MUTE OPTION
L
1
2.
There are 6 levels of volume selections. Use or
key to adjust.
3.
The new setting will remain effective for all future calls
until changed.
~33~
3.
If the handset is not on the cradle and MENU-5-2 “Any Key Talk” setting is “On,”
press any key (except and the SILENT soft key) to answer.
Notes:
1. The LCD displays the caller’s Handset ID.
2. You can press the SILENT (Left) soft key if you choose to ignore the call.
Unlike turning off the ringer the SILENT key operation is valid only for
the current call.
Ending a Call
To end a telephone or intercom call, press key, or place handset into charger
cradle.
Adjusting Handset Receiver (Earpiece) Voice Volume
1.
Voice volume can only be adjusted during a call.
00:00:15
Volume: 3
11
MUTE OPTION
L
1
2.
There are 6 levels of volume selections. Use or
key to adjust.
3.
The new setting will remain effective for all future calls
until changed.
Adjusting Handset Speakerphone Voice Volume
1.
Voice volume can only be adjusted during a call (in
speakerphone mode).
00:00:15
Volume: 3
11
MUTE OPTION
L
1
2.
There are 6 levels of volume selections. Use or
key to adjust.
3.
The new setting will remain effective for all future calls
until changed.
~34~
Placing a Call On Hold
1.
When a call is in progress, it can be put on hold by pressing
OPTION (Right
) soft
key and the ＊ key.
You have a
call on hold
UNHOLD OPTION
2.
To return to the conversation, press UNHOLD (Left) soft
key.
Notes:
1. Handset LCD displays when a call is on hold. An alert tone (a beep)
every 30-seconds will remind the handset that a call is on hold.
2. If the operation (e.g., call transfer) fails after putting a call on-hold,
the held call may be dropped.
Mute
1.
After a link is established, you can press MUTE (Left) soft
key to mute the handset microphone.
00:00:15
MUTE
11
UNMUTE OPTION
L
1
2.
When mute is active, the other end will not hear your
voice, but can still speak to you.
3.
To leave the mute state, press UNMUTE (Left) soft key. Mute is effective only
for the current call.
Do Not Disturb (Silent Ring)
1.
Enter the key sequence MENU-3-1, then select “Off.” Press
SELECT (Left) soft key to confirm your choice. This will turn
off the ringer until it is turned on again from the menu.
Joe
033289289
SILENT
11
L
1
2.
For temporary silencing the ringer when an incoming call
arrives, press SILENT (Left) soft key.