Epson EB-992F User Manual

Copying Menu Settings Between Projectors (Batch Setup)
153
After selecting the projector's menu settings for one projector, you can use the
following methods to copy the settings to other projectors, as long as they are
the same model.
• by using a USB flash drive (Available only for models that have a USB-A
port.)
• by connecting a computer and projector using a USB cable
• by using Epson Projector Management (Available only for models that have
a LAN port.)
Menu settings such as the following are not copied to the other projector.
• Network menu settings (except for the Notifications menu and the Others
menu)
• Lamp Hours and Status from the Projector Info menu
a
• Perform batch setup before adjusting the image settings such as
keystone distortion correction. Since image adjustment values are
also copied to another projector, the adjustments you made before
performing the batch setup are overwritten and the projected screen
you adjusted may change.
• When copying the menu settings from one projector to another,
user's logo is also copied. Do not register the information that you do
not want to share between multiple projectors as a user's logo.
• Make sure Batch Setup Range is set to Limited if you do not want to
copy the following settings:
• Password Protection settings
• Network menu settings (except for the Notifications menu and
the Others menu)
s Extended > Operation > Advanced > Batch Setup Range
Caution
Epson takes no responsibility for batch setup failures and associated repair costs
due to power outages, communication errors, or other problems that may cause
such failures.
gg Related Links
• "Transferring Settings From a USB Flash Drive" p.153
• "Transferring Settings From a Computer" p.154
• "List of Functions" p.10
Transferring Settings From a USB Flash Drive
You can copy menu settings from one projector to another of the same model
using a USB flash drive.
a
The USB flash drive must use a FAT format and not incorporate any
security function. Delete any files on the drive before using it for batch
setup or the settings may not be saved correctly.
a
Disconnect the power cord from the projector, and check that all of the
projector's indicators have turned off.
b
Connect an empty USB flash drive directly to the projector's USB-A
port.
c
Hold down the [Esc] button on the remote control or the control panel
and connect the power cord to the projector.
d
When all of the projector's indicators turn on, release the [Esc] button.
The indicators start flashing and the batch setup file is written to the
USB flash drive. When writing is finished, the projector turns off.
Caution
Do not disconnect the power cord or the USB flash drive from the projector
while the file is being written. If the power cord or USB flash drive is
disconnected, the projector may not start correctly.
e
Remove the USB flash drive.

Epson EB-992F Specifications

General

Matrix size	0.61 \
Number of colors	1.07 billion colors
Native aspect ratio	16:9
Projection distance	1.76 - 2.86 m
Vertical scan range	100 - 120 Hz
Projection technology	3LCD
Contrast ratio (typical)	16000:1
Screen size compatibility	30 - 300 \
Projector native resolution	1080p (1920x1080)
Keystone correction, vertical	-30 - 30 °
Projector brightness (economic mode)	2400 ANSI lumens
Lamp type	UHE
Lamp power	230 W
Light source type	Lamp
Service life of light source	6500 h
Service life of light source (economic mode)	17000 h
3D	No
Full HD	Yes
Video processing	10 bit
Video color modes	Blackboard, Cinema, Dynamic, Presentation, sRGB
Analog signal format system	-
Throw ratio	1.32 - 2.14:1
Focal length range	18.2 - 29.2 mm
Aperture range (F-F)	1.51 - 1.99
Placement	Ceiling, Desktop
Product type	Standard throw projector
Product color	White
Cable lock slot type	Kensington
RMS rated power	16 W
Power source	AC
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	- W
Power consumption (typical)	327 W
Power consumption (economy mode)	225 W
Storage temperature (T-T)	-10 - 60 °C
Operating temperature (T-T)	5 - 40 °C
Storage relative humidity (H-H)	10 - 90 %
Operating relative humidity (H-H)	20 - 80 %
Cables included	AC, HDMI
Bundled software	EasyMP Multi PC Projection, Epson Projektor Management
HDMI connector type	Full-size
Serial interface type	RS-232C
USB 2.0 ports quantity	1
Noise level	37 dB
Country of origin	Philippines
Noise level (economic mode)	28 dB
USB display function	3 in 1: Image / Mouse / Sound
Supported network protocols	PJLink
Pallet weight	0 g
Quantity per pack	1 pc(s)
Quantity per pallet	72 pc(s)
Harmonized System (HS) code	85286200
Software support	via: AMX, Crestron (Network), Control4, Extron

Weight and Dimensions

Depth	282 mm
Width	309 mm
Height	90 mm
Weight	3100 g
Package depth	390 mm
Package width	385 mm
Package height	170 mm
Package weight	4592 g