Epson EB-992F User Manual

Copying Menu Settings Between Projectors (Batch Setup)
155
i
Connect the USB cable to the computer's USB port and to the
projector's USB-B port.
j
Hold down the [Menu] button on the remote control or the control
panel and connect the power cord to the projector.
k
When all of the projector's indicators turn on, release the [Menu]
button.
The computer recognizes the projector as a removable disk.
l
Copy the batch setup file (PJCONFDATA.bin) that you saved to your
computer to the top level folder of the removable disk.
a
Do not copy any files or folders other than the batch setup file to
the removable disk.
m
Eject the USB device (Windows) or drag the removable disk icon to the
Trash (Mac).
n
Disconnect the USB cable.
When all of the indicators start flashing, the settings are being written.
When writing is finished, the projector turns off.
Caution
Do not disconnect the power cord from the projector while the file is being
written. If the power cord is disconnected, the projector may not start
correctly.
gg Related Links
• "Batch Setup Error Notification" p.155
Batch Setup Error Notification
The projector's indicators notify you if an error occurs during a batch setup
operation. Check the status of the projector's indicators and follow the
instructions described in the table here.
Indicator status Problem and solutions
• Lamp: Orange - flashing
fast
• Temp: Orange - flashing
fast
The batch setup file may be corrupt, or the USB flash
drive or USB cable may not be connected correctly.
Disconnect the USB flash drive or the USB cable,
unplug and then plug in the projector's power cord, and
then try again.
• Power: Blue - flashing
fast
• Status: Blue - flashing
fast
• Lamp: Orange - flashing
fast
• Temp: Orange - flashing
fast
Writing the settings may have failed and an error may
have occurred in the projector's firmware.
Stop using the projector, remove the power plug from
the electrical outlet. Contact Epson for help.
gg Related Links
• "Projector Indicator Status" p.169

Epson EB-992F Specifications

General

Matrix size	0.61 \
Number of colors	1.07 billion colors
Native aspect ratio	16:9
Projection distance	1.76 - 2.86 m
Vertical scan range	100 - 120 Hz
Projection technology	3LCD
Contrast ratio (typical)	16000:1
Screen size compatibility	30 - 300 \
Projector native resolution	1080p (1920x1080)
Keystone correction, vertical	-30 - 30 °
Projector brightness (economic mode)	2400 ANSI lumens
Lamp type	UHE
Lamp power	230 W
Light source type	Lamp
Service life of light source	6500 h
Service life of light source (economic mode)	17000 h
3D	No
Full HD	Yes
Video processing	10 bit
Video color modes	Blackboard, Cinema, Dynamic, Presentation, sRGB
Analog signal format system	-
Throw ratio	1.32 - 2.14:1
Focal length range	18.2 - 29.2 mm
Aperture range (F-F)	1.51 - 1.99
Placement	Ceiling, Desktop
Product type	Standard throw projector
Product color	White
Cable lock slot type	Kensington
RMS rated power	16 W
Power source	AC
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	- W
Power consumption (typical)	327 W
Power consumption (economy mode)	225 W
Storage temperature (T-T)	-10 - 60 °C
Operating temperature (T-T)	5 - 40 °C
Storage relative humidity (H-H)	10 - 90 %
Operating relative humidity (H-H)	20 - 80 %
Cables included	AC, HDMI
Bundled software	EasyMP Multi PC Projection, Epson Projektor Management
HDMI connector type	Full-size
Serial interface type	RS-232C
USB 2.0 ports quantity	1
Noise level	37 dB
Country of origin	Philippines
Noise level (economic mode)	28 dB
USB display function	3 in 1: Image / Mouse / Sound
Supported network protocols	PJLink
Pallet weight	0 g
Quantity per pack	1 pc(s)
Quantity per pallet	72 pc(s)
Harmonized System (HS) code	85286200
Software support	via: AMX, Crestron (Network), Control4, Extron

Weight and Dimensions

Depth	282 mm
Width	309 mm
Height	90 mm
Weight	3100 g
Package depth	390 mm
Package width	385 mm
Package height	170 mm
Package weight	4592 g