Exmark Lazer LZS User Manual (English)

Questions and Answers:

U
uwrightSep 6, 2025
Why don't the blades rotate on my Exmark Lawn Mower?
- K
  Katherine DuncanSep 6, 2025
  If the blades on your Exmark Lawn Mower do not rotate, check the drive belt tension. Install a new deck belt if the current one is worn, loose, or broken. If the deck belt is off the pulley, reinstall it on the clutch and deck pulleys, idlers, and tensioning idler per the routing decal on the deck. Replace the idler spring if it's broken or missing. Ensure the drive belt is routed correctly, referring to the belt routing decal on the deck.
M
Matthew Bradford Jr.Sep 6, 2025
How to stop abnormal vibration in my Exmark Lawn Mower?
- D
  dianeallenSep 6, 2025
  If your Exmark Lawn Mower is experiencing abnormal vibration, replace bent or unbalanced cutting blades. Tighten the blade mounting bolt and the engine mounting bolts. Also, tighten any loose engine, idler, or blade pulleys. For a damaged engine pulley or bent blade spindle, consider contacting an Authorized Service Dealer.
D
Daniel PhamSep 5, 2025
What to do if my Exmark Lawn Mower engine overheats?
- E
  Ellen WoodwardSep 5, 2025
  If your Exmark Lawn Mower engine is overheating, remove any debris from around the radiator. Reduce the ground speed if the engine load is excessive. Ensure the oil level in the crankcase is adequate, adding oil if low. Clear any obstructions from the engine's cooling fins and air passages. For issues related to coolant level, refer to Check Engine Coolant Level section in the Maintenance.
T
Terri HallAug 23, 2025
What to do if the starter does not crank on my Exmark Lazer LZS Lawn Mower?
- C
  cmcdanielAug 25, 2025
  If the starter on your Exmark Lawn Mower isn't cranking, make sure the PTO is disengaged and the parking brake is set. Also, confirm the drive levers are in the neutral lock position. Check if the battery has a full charge and inspect electrical connections for corrosion or looseness, cleaning and reconnecting them if necessary. Replace any blown fuses. If these steps don't resolve the issue, it could be a defective relay, switch, or module, requiring professional service.
B
Brandon JonesSep 3, 2025
Why does my Exmark Lawn Mower engine lose power?
- J
  Justin BarrettSep 3, 2025
  If your Exmark Lawn Mower engine loses power, start by reducing ground speed if the engine load is excessive. Check and clean or replace the air cleaner if it's dirty. Ensure the oil level in the crankcase is adequate, adding oil if low. Clear any obstructions from the engine's cooling fins and air passages. Replace the fuel filter if it's dirty. For issues related to dirt, water, or stale fuel in the fuel system, consider contacting an authorized service dealer.
J
Joseph Newman MDSep 2, 2025
What does it mean if the oil pressure light is on and the engine RPM is low on my Exmark Lawn Mower?
- W
  Whitney RiceSep 2, 2025
  If the oil pressure light is on and the engine RPM is low on your Exmark Lawn Mower, it means that the Engine Control Unit has limited engine RPMs, known as “limp” mode. Let engine cool and check oil level. If level is above 'add', contact an Authorized Service Dealer.
S
Samantha RyanSep 1, 2025
What should I do if the blades on my Exmark Lazer LZS don't rotate?
- K
  Kyle GarciaSep 1, 2025
  If the blades on your Exmark Lawn Mower do not rotate: * The deck belt might be worn, loose, or broken: Install new deck belt. * The deck belt might be off the pulley: Install belt on clutch and deck pulleys, idlers, and tensioning idler per routing decal on deck. * A spring might be broken or missing: Replace the spring. * The drive belt might not be routed correctly: Refer to belt routing decal on deck.
J
Jamie GibsonAug 31, 2025
What to do if my Exmark Lawn Mower pulls to the left or right?
- B
  Brandon WalkerSep 1, 2025
  If your Exmark Lawn Mower pulls to the left or right with the levers fully forward, you should: * Check the air pressure in the tires, ensuring 13 psi for drive tires and 13 psi for pneumatic casters. * Check the reverse indicator and motion control linkage adjustment.
C
Cameron PadillaAug 31, 2025
How to fix uneven cuts with my Exmark Lawn Mower?
- C
  Cynthia ScottAug 31, 2025
  To fix uneven cuts with your Exmark Lawn Mower, consider the following: * Check the air pressure in the tires, ensuring they are at 13 psi for both the drive tires and pneumatic casters. * Inspect the deck support chains. * Check the blades tip to tip for straightness (they should be within 3/16" or one blade width from being in line.)
T
turneraliciaAug 30, 2025
How to fix Exmark Lawn Mower that pulls left or right?
- J
  jacksonjenniferAug 30, 2025
  If your Exmark Lawn Mower pulls to the left or right with the levers fully forward, check the air pressure in the drive tires, ensuring they are at 13 psi. Also, inspect the reverse indicator and motion control linkage adjustment.