Why does my Exmark Lazer LZS cut unevenly?
If your Exmark Lawn Mower cuts unevenly, start by checking the air pressure in the drive tires to ensure they are at 13 psi. Inspect the deck support chains and verify the deck leveling. Also, check the blades tip to tip for straightness, ensuring they are within 3/16" or one blade width from being in line.
How to fix an Exmark Lazer LZS Lawn Mower that cuts unevenly?
If your Exmark Lawn Mower cuts unevenly, consider the following: * Check the air pressure in the drive tires, it should be 13 psi. Semi-pneumatic casters do not require inflation. * Inspect the deck support chains. * Check the blades tip to tip for straightness (they should be within 3/16" or one blade width from being in line.)
Why won't my Exmark Lawn Mower starter crank?
The starter may not crank for several reasons: * The PTO might be engaged: Disengage the PTO. * The parking brake might not be engaged: Set the parking brake. * The drive levers might not be in the neutral lock position: Ensure the drive levers are in the neutral lock position. * The battery might not have a full charge: Charge the battery. * Electrical connections might be corroded, loose, or faulty: Check the electrical connections for good contact, clean connector terminals, apply dielectric grease, and reconnect. * A fuse might be blown: Replace the blown fuse. * Relay or switch is defective: Contact an Authorized Service Dealer. * Faulty module: Replace module.
Why won't my Exmark Lawn Mower engine start?
If your Exmark Lawn Mower engine won't start, several factors could be the cause. Here are some things to check: * Ensure the battery is fully charged. * Position the throttle control midway between “SLOW” and “FAST,” and set the choke to “ON” for a cold engine or “OFF” for a warm one. * Confirm there's fuel in the tank and the fuel valve is open. * Verify the seat switch is properly adjusted. * Make sure the parking brake is set and motion control levers are in the neutral lock position. * Confirm the PTO is disengaged. * Check that the spark plug wires are properly connected. * Inspect for loose or faulty wiring connections and corrosion at all wiring connections. Clean any corrosion with electrical contact cleaner, apply dielectric grease, and reconnect.
What to do if my Exmark Lazer LZS Lawn Mower engine will not start?
If your Exmark Lawn Mower engine won't start, starts hard, or fails to keep running, consider the following: * The fuel tank might be empty, so fill it up. * The fuel shutoff valve could be closed, so open it. * The oil level in the crankcase might be low, so add oil. * The throttle and choke may not be correctly positioned; ensure the throttle is midway between “SLOW” and “FAST,” and the choke is “ON” for a cold engine or “OFF” for a warm engine. * A dirty fuel filter can cause starting issues, so replace it. * A dirty air cleaner can prevent the engine from starting; clean or replace the air cleaner element. * Check the seat switch indicator. Replace seat if needed. * Also, check the spark plug wire connection and clean, adjust, or replace the spark plug if faulty.
Why my Exmark Lawn Mower engine will not start?
If your Exmark Lawn Mower engine won't start, starts hard, or fails to keep running, first ensure the fuel tank isn't empty and the fuel shutoff valve is open. Check the oil level in the crankcase and add oil if needed. Make sure the throttle and choke are in the correct positions. Replace the fuel filter if it's dirty, and inspect/clean or replace the air filter. Inspect the spark plug wire connection and clean, adjust, or replace the spark plug. Also, check the seat switch indicator and replace the seat if needed. Inspect the electrical connections for good contact, cleaning them as necessary. For issues related to stale fuel, or defective relay, switch, or module, consider contacting an authorized service dealer.
General| Brand | Exmark |
|---|---|
| Model | Lazer LZS |
| Category | Lawn Mower |
| Language | English |
To Next Page