14
2.9.7 Cutting Height Adjustment: an extra-long cushioned lever is used to adjust the
cutting height from 1” (2.5 cm) to 4.5” (11.4 cm.) in 1/4” (.64 cm.) increments.
The cutting height adjustment handle has a transport position and all adjustments
can be made while the operator remains seated. The foot operated deck lift
assist lever aids in raising the deck.
2.9.8 Mulching Kit: Optional.
2.10 DIMENSIONS
2.10.1 Overall Width:
Without deck Discharge chute up Discharge chute down
w/46” Deck 44.9 in. (114.1 cm) 49.5 in. (125.7 cm) 58.5 in. (148.6 cm)
w/50” Deck 46.5 in. (118.1 cm) 51.1 in. (129.8 cm) 62.7 in. (159.3 cm)
w/56” Deck 48.5 in. (123.2 cm) 57.3 in. (145.5 cm) 68.9 in. (175.0 cm)
2.10.2 Overall Length:
w/46” Deck w/50” Deck w/56” Deck
Roll Bar - Up 76.4 in. (194.1 cm) 76.9 in. (195.3 cm) 82.0 in. (208.3 cm)
Roll Bar - Down 82.4 in. (209.3 cm) 82.9 in. (210.6 cm) 88.0 in (223.5 cm)
2.10.3 Overall Height:
Roll Bar - Up Roll Bar - Down
69.9 in. (177.5 cm) 51.8 in. (131.6 cm)
2.10.4 Tread Width: (center to center of tires, widthwise)
w/46” Deck w/50” Deck w/56” Deck
Drive Wheels
34.4 in. (87.4 cm) 36.4 in. (92.5 cm) 38.4 in. (97.5 cm)
Front Casters
2.75 in. (75.6 cm) 31.9 in. (81.0 cm) 33.3 in. (84.6 cm)
2.10.5 Wheel Base: (center of caster tire to center of drive tire)
w/46” Decks w/50” Decks w/56” Deck
48.0 in. (121.9 cm) 48.5 in. (123.2 cm) 52.0 in. (132.1 cm)
2.10.6 Curb Weight:
w/46” Deck w/50” Deck w/56” Deck
1080 lbs. (490 kg) 1135 lbs. (515 kg) 1190 lbs. (540 kg)
* Note: Weight will vary slightly, depending on engine option.
2.11 TORQUE REQUIREMENTS
Bolt Location Torque
Blade Drive Sheave Mounting Nut ................................90-110 ft-lbs. (122-149 N-m)
Cutter Housing Spindle Nut.........................................160-185 ft-lbs. (217-251 N-m)
Blade Mounting Bolt (lubricate with anti-seize)....................55-60 ft-lbs. (75-81 N-m)
Engine Deck/Front Frame Mount Bolts ...............................30-35 ft-lbs. (41-47 N-m)
Anti-Scalp Roller (See Figure 5)
Nyloc Nut ...................................................................30-35 ft-lbs. (41-47 N-m)
Hex Capscrew ............................................................50-55 ft-lbs. (68-75 N-m)
Engine Mounting Bolts .......................................................15-20 ft-lbs. (20-27 N-m)
Wheel Motor Mounting Bolts.............................................72-77 ft-lbs. (98-104 N-m)
Wheel Hub Slotted Nut ...............................................minimum125 ft-lbs. (169 N-m)
Wheel Lug Nuts ..............................................................90-95 ft-lbs. (122-129 N-m)
Rollover Protection System (Roll Bar) Mounting Bolts.........30-35 ft-lbs. (41-47 N-m)
Deck Drive Jackshaft Nut.................................................75-80 ft-lbs (102-108 N-m)
Clutch Retaining Bolt (secured with threadlocker)...............55-60 ft-lbs. (75-81 N-m)
To Next Page
Loading...
