Exmark Lazer Z XS User Manual (English)

Other manuals for Exmark Lazer Z XS

Parts Manual32 pages

Setup Instructions5 pages

Questions and Answers:

T
taylorlaurenAug 21, 2025
What to do if my Exmark Lawn Mower engine will not start?
- K
  Kelly JonesAug 22, 2025
  If your Exmark Lawn Mower engine won't start, starts hard, or fails to keep running, several factors could be the cause. First, ensure the fuel tank is filled and the fuel shutoff valve is open. Check the oil level in the crankcase and add oil if it's low. Make sure the throttle control is midway between the 'SLOW' and 'FAST' positions. Other potential issues include a dirty fuel filter (replace it), a dirty air cleaner (clean or replace the element), or corroded, loose, or faulty electrical connections (check and clean them). For dirt, water, or stale fuel in the fuel system or a defective relay or switch, it's best to contact an Authorized Service Dealer.
J
Joseph MeyersAug 23, 2025
What to do if my Exmark Lazer Z XS starter does not crank?
- R
  Rhonda FranklinAug 23, 2025
  If the starter on your Exmark Lawn Mower doesn't crank, there are several things to check: * Ensure the PTO is disengaged. * Set the parking brake. * Make sure the drive levers are in the neutral lock position. * Check if the battery has a full charge and charge it if necessary. * Inspect electrical connections for corrosion or looseness; clean and reconnect them. * Replace any blown fuses. If these steps don't resolve the issue, the relay or switch may be defective, and you should contact an Authorized Service Dealer.
K
Kevin LawsonAug 25, 2025
What to do if the starter does not crank on my Exmark Lazer Z XS Lawn Mower?
- J
  Joanna SnyderAug 26, 2025
  If the starter on your Exmark Lawn Mower doesn't crank, several factors could be at play. First, ensure the PTO is disengaged. Next, verify that the parking brake is fully set and that the drive levers are in the neutral lock position. Check the battery charge and charge if necessary. Examine all electrical connections for corrosion or looseness; clean them with electrical contact cleaner, apply dielectric grease, and reconnect. Replace any blown fuses. If these steps don't resolve the issue, the relay or switch may be defective, requiring assistance from an Authorized Service Dealer.
F
floresrobertAug 27, 2025
What to do if my Exmark Lazer Z XS engine overheats?
- C
  Crystal LynchAug 27, 2025
  If your Exmark Lawn Mower engine is overheating, there are several potential causes. First, the engine load might be excessive, so reduce the ground speed. Check the oil level in the crankcase and add oil if it's low. A dirty air filter can also cause overheating, so clean or replace the air cleaner element. Ensure the coolant level is adequate and add coolant if necessary. Also, check for any debris on or around the radiator and remove it. If the water pump or alternator belt is worn, loose, or broken, contact an Authorized Service Dealer.
F
Frances HansonAug 29, 2025
Why is my Exmark Lawn Mower cutting height uneven?
- S
  Stephanie MasonAug 29, 2025
  An uneven cutting height on your Exmark Lawn Mower can result from several factors. The blades might not be sharp, so sharpen them. Bent cutting blades can also cause this, so install new ones. Check if the mower deck is level and adjust it from side-to-side and front-to-rear if necessary. A dirty mower underside can also contribute, so clean it. Ensure the tire pressure in the drive tires is correct, and adjust if needed. For a bent blade spindle or uneven cutting height of adjacent blade tips, it is best to contact an Authorized Service Dealer or replace blades, spindles and (or) check for damage to mower deck.
T
Tamara WhiteAug 30, 2025
Why does my Exmark Lazer Z XS Lawn Mower vibrate abnormally?
- A
  Amanda EdwardsAug 30, 2025
  Abnormal vibration in your Exmark Lawn Mower can be attributed to several issues. Bent or unbalanced cutting blades are a common cause, so install new cutting blades. Check if the blade mounting bolt is loose and tighten it. Also, inspect the engine mounting bolts and tighten them if necessary. Loose engine, idler, or blade pulleys can also cause vibration, so tighten the appropriate pulley. If the engine pulley is damaged, or the blade spindle is bent, or the belt is damaged, contact an Authorized Service Dealer or install new belt.
S
smithheatherAug 31, 2025
What to do if my Exmark Lawn Mower blades do not rotate?
- C
  Christopher PhillipsSep 1, 2025
  If the blades on your Exmark Lawn Mower aren't rotating, start by checking the drive belt tension. If the drive belt is off the pulley, check it for damage and replace if necessary, then reinstall it, ensuring the belt guide is correctly positioned. If the deck belt is worn, loose, or broken, install a new one. If the deck belt is off the pulley, install it and check the idler pulley, idler arm, and spring for correct position and function. Finally, a broken or missing idler spring can prevent blade rotation, so replace the spring.
S
Sean JordanSep 2, 2025
Why does my Exmark Lazer Z XS Lawn Mower pull left or right?
- A
  Amy JonesSep 2, 2025
  If your Exmark Lawn Mower pulls to the left or right, with levers fully forward, it may be due to tracking needing adjustment, so adjust the tracking. Also, check the tire pressure in the drive tires and adjust as necessary. Finally, the reverse indicator and motion control linkage might need adjustment, so adjust them.
T
Taylor TaylorSep 3, 2025
How to fix uneven cuts with my Exmark Lazer Z XS?
- J
  John FordSep 3, 2025
  If your Exmark Lawn Mower cuts unevenly, start by checking the air pressure in the drive tires, ensuring they are at 10 psi. Then, inspect the deck support chains and deck leveling. Finally, check the blades tip to tip for straightness, ensuring they are within 3/16" or one blade width from being in line.
X
xperezSep 5, 2025
Why is my Exmark Lazer Z XS engine losing power?
- V
  vwrightSep 5, 2025
  If your Exmark Lawn Mower engine is losing power, try reducing the ground speed to lessen the engine load. Clean or replace the air cleaner element if it's dirty. Ensure the oil level in the crankcase is adequate by adding oil if needed. Clear any obstructions from the engine's cooling fins and air passages to improve airflow. Check the fuel cap's vent hole and clean or replace the cap if the vent is plugged. Replace the fuel filter if it's clogged with dirt. If the problem persists, there may be dirt, water, or stale fuel in the fuel system, and you should contact an Authorized Service Dealer.

Exmark Lazer Z XS Specifications

General

Brand	Exmark
Model	Lazer Z XS
Category	Lawn Mower
Language	English

Summary

Introduction

Before Operating Your Mower

Read this manual entirely before operating the mower for safety and efficiency.

Safety

Safety Alert Symbol

Explains the meaning and usage of the safety alert symbol and signal words.

Safe Operating Practices

Outlines essential practices for safe operation, including training and preparation.

Slope Operation

Provides essential safety guidelines and warnings for operating on slopes.

Using the Rollover Protection System (ROPS)

Details the importance and correct usage of the Rollover Protection System (roll bar).

Safety and Instructional Decals

Highlights the importance of legible and correctly placed safety signs on the machine.

Specifications

Model Numbers

Lists the specific model numbers covered by this manual.

Engine

Provides specifications for the mower's engine.

Fuel System

Details specifications related to the fuel tank, filter, and gauge.

Electrical System

Outlines specifications for the charging system, battery, and fuses.

Safety Interlock System

Explains the safety interlock system requirements for starting the engine.

Cooling System

Provides details on the cooling system, including coolant type and capacity.

Operator Controls

Describes the steering, motion control, PTO, brake, and deck height adjustment controls.

Seat

Details the specifications of the operator's seat.

Hydrostatic Ground Drive System

Outlines specifications for the hydrostatic pumps, wheel motors, and oil.

Tires & Wheels

Lists tire sizes, ply rating, pressure, and tread types.

Cutting Deck

Provides specifications for the deck, including cutting width, depth, and blade size.

Cutting Height Adjustment

Explains how to adjust the mower deck's cutting height.

Dimensions

Lists the overall width, length, and height dimensions of the mower.

Torque Requirements

Specifies torque values for various bolts and nuts on the machine.

Operation

Product Overview and Controls

Provides a visual overview of components and details key operator controls.

Fueling and Pre-Start Procedures

Covers fuel selection, pre-start checks, and tank filling instructions.

Starting and Operating Instructions

Details ROPS, fuel shut-off valve, and engine starting procedures.

Engaging and Disengaging PTO

Step-by-step instructions for engaging and disengaging the Power Take-Off (PTO).

Stopping the Engine

Procedures for safely shutting down the engine.

Driving the Machine

Explains how to start moving, turn, and stop the mower safely.

Adjusting Cutting Height and Rollers

Describes how to adjust cutting height and anti-scalp rollers.

Transporting and Loading

Guidelines for safely transporting and loading the mower onto vehicles.

Maintenance

Recommended Maintenance Schedule(s)

Provides a comprehensive schedule for regular maintenance tasks.

Engine Oil and Filter Maintenance

Details procedures for checking and changing engine oil and filters.

Belt and Pulley Maintenance

Covers checking belt condition and lubricating pulleys.

Lubrication Procedures

Explains how to lubricate various grease fittings and hubs.

Fuel System Maintenance

Covers draining and changing fuel filters/water separators.

Cooling System Maintenance

Procedures for checking and changing engine coolant.

Adjustments

Provides instructions for various adjustments to the mower.

Deck Leveling

Detailed procedure for ensuring the mower deck is properly leveled.

Belt Tension Adjustments

Covers pump, mule, deck, and alternator belt tensioning.

Brake System Maintenance

Includes brake link and main brake adjustment procedures.

Motion Control Linkage Adjustment

Instructions for adjusting the motion control linkage for proper drive.

Cleaning Procedures

Covers cleaning the engine cooling system, radiator, and debris removal.

Troubleshooting

A guide to diagnosing and resolving common mower problems.

Schematics

Electrical Diagram

Provides a visual representation of the mower's electrical system wiring.

Electrical Logic Schematic

Illustrates the logical flow of electrical signals within the mower's system.

Hydraulic Diagram

Shows the layout and connections of the mower's hydraulic system components.

Exmark Commercial Turf Equipment 2 Year Limited Warranty

Conditions and Products Covered

Outlines the conditions and products included under the limited warranty.

Warranty Exceptions

Lists items and conditions that are not covered by the warranty.

Items and Conditions Not Covered

Specifies exclusions from the warranty coverage.

Instructions for Obtaining Warranty Service

Provides guidance on how to obtain warranty service for the product.

Owner's Responsibilities

Details the owner's duties for maintaining and servicing the equipment.

General Conditions

Explains general terms, limitations, and legal rights related to the warranty.

ACCESSORIES AND OPTIONS

MID-MOUNT RIDING ACCESSORIES AND OPTIONS

Lists available accessories and options for mid-mount riding mowers.

OUT-FRONT RIDING ACCESSORIES AND OPTIONS

Lists available accessories and options for out-front riding mowers.

WALK-BEHIND ACCESSORIES AND OPTIONS

Lists available accessories and options for walk-behind mowers.

Related product manuals

Exmark Lazer Z XP

60 pages

Exmark LAZER Z X Series

Exmark Lazer Z HP 465

48 pages

Exmark LAZER Z S-SERIES

64 pages

Exmark LAZER Z E Series

76 pages

Exmark LAZER Z LZ27KC604

48 pages

Exmark LAZER Z ADVANTAGE SERIES

52 pages

Exmark Lazer Z Air-cooled series

5 pages

Exmark Lazer Z XS User Manual

Table of Contents

Other manuals for Exmark Lazer Z XS

Questions and Answers:

Exmark Lazer Z XS Specifications

Summary

Introduction

Before Operating Your Mower

Safety

Safety Alert Symbol

Safe Operating Practices

Slope Operation

Using the Rollover Protection System (ROPS)

Safety and Instructional Decals

Specifications

Model Numbers

Engine

Fuel System

Electrical System

Safety Interlock System

Cooling System

Operator Controls

Seat

Hydrostatic Ground Drive System

Tires & Wheels

Cutting Deck

Cutting Height Adjustment

Dimensions

Torque Requirements

Operation

Product Overview and Controls

Fueling and Pre-Start Procedures

Starting and Operating Instructions

Engaging and Disengaging PTO

Stopping the Engine

Driving the Machine

Adjusting Cutting Height and Rollers

Transporting and Loading

Maintenance

Recommended Maintenance Schedule(s)

Engine Oil and Filter Maintenance

Belt and Pulley Maintenance

Lubrication Procedures

Fuel System Maintenance

Cooling System Maintenance

Adjustments

Deck Leveling

Belt Tension Adjustments

Brake System Maintenance

Motion Control Linkage Adjustment

Cleaning Procedures

Troubleshooting

Troubleshooting

Schematics

Electrical Diagram

Electrical Logic Schematic

Hydraulic Diagram

Exmark Commercial Turf Equipment 2 Year Limited Warranty

Conditions and Products Covered

Warranty Exceptions

Items and Conditions Not Covered

Instructions for Obtaining Warranty Service

Owner's Responsibilities

General Conditions

ACCESSORIES AND OPTIONS

MID-MOUNT RIDING ACCESSORIES AND OPTIONS

OUT-FRONT RIDING ACCESSORIES AND OPTIONS

WALK-BEHIND ACCESSORIES AND OPTIONS

Related product manuals