Exmark METRO User Manual (English)

Other manuals for Exmark METRO

Operator's Manual48 pages

Setup Instructions7 pages

Questions and Answers:

T
Teresa WilsonAug 15, 2025
What to do if my Exmark METRO Lawn Mower engine will not start?
- J
  Jennifer MckayAug 15, 2025
  If your Exmark Lawn Mower's engine won't start, ensure the transmission is in the 'true neutral' position. Also, verify that the blades are disengaged and the blade switch is depressed. Confirm there is fuel in the tank and the fuel valve is open. Check that the spark plug wire(s) are properly connected and inspect for loose or faulty wiring connections, including corrosion. Clean any corroded connector terminals, apply dielectric grease, and reconnect.
T
Taylor McclureAug 18, 2025
Why won't my Exmark METRO engine start?
- L
  lunamarkAug 18, 2025
  If your Exmark Lawn Mower engine won't start, several factors could be at play. Here’s what to check: * Ensure the engine is properly choked. * Verify the transmission is in the "true neutral" position. * Confirm the PTO is disengaged and the PTO switch is depressed. * Check that there is fuel in the tank and the fuel valve is open. * Make sure the spark plug wire(s) is/are properly connected. * Inspect for loose or faulty wiring connections. * Look for corrosion at all wiring connections; clean connector terminals, apply dielectric grease, and reconnect. * For Kawasaki engines: Ensure the key switch is in the “Run” position.
B
Benjamin WalkerAug 21, 2025
Why is my Exmark METRO Lawn Mower pulling to the left or right?
- J
  Jeffrey FarrellAug 21, 2025
  If your Exmark Lawn Mower is pulling to the left or right, check the idler arm pulleys and drive sheaves for mud or grass buildup and ensure the scraper is properly installed. Verify that the idler arms pivot freely; if not, lubricate the idler pivots. Inspect for worn drive belts. Also, check the tire pressure in the drive tires, ensuring it's between 12 to 16 psi. You might use higher pressure (up to 28 psi) on the side it's pulling towards, but be aware that different pressures may cause an uneven cut.
C
courtney66Aug 25, 2025
How to fix an Exmark METRO Lawn Mower that cuts unevenly?
- K
  kerri74Aug 25, 2025
  To fix an Exmark Lawn Mower that cuts unevenly, start by checking the drive tire pressure and tire circumference. Remember that higher tire pressure on rough terrain may provide a more uniform cutting height, while lower pressure offers more flotation. Check the blade spacers, axle positions, and front caster spacers, ensuring they are equal on each blade. Confirm that all bolts on the caster mounting brackets are tight. Also, check the blades tip to tip for straightness, ensuring they are within 3/16" or one blade width from being in line.
S
Sara MiddletonAug 27, 2025
What to do if Exmark METRO is pulling to the left or right?
- W
  Wendy FitzgeraldAug 27, 2025
  If your Exmark Lawn Mower is pulling to the left or right, consider these possible solutions: * Inspect idler arm pulleys and drive sheaves for any buildup of mud or grass. * Ensure idler arms can pivot freely; if they don't, lubricate the idler pivots. * Examine drive belts for wear; avoid using a new belt with a worn one. * Verify proper tire pressure in the drive tires, with a recommendation of 12 to 16 psi (82 –110 kPa). You might use higher pressure (up to 28 psi or 193 kPa) on the side it pulls towards.
J
Jessica LeeAug 30, 2025
Why does my Exmark Lawn Mower cut unevenly?
- S
  Stephen LeeAug 30, 2025
  If your Exmark Lawn Mower cuts unevenly, here's what you should check: * Verify the drive tire pressure and tire circumference are correct. * Ensure blade spacers, axle positions, and front caster spacers are equal on each blade. * Check that all bolts on the caster mounting brackets are tight. * Confirm the blades are straight tip to tip, within 3/16" (.47 cm) or one blade width from being in line.
B
barneskimberlySep 2, 2025
What to do if my Exmark Lawn Mower is pulling to the left or right?
- E
  Erin GarrisonSep 2, 2025
  If your Exmark Lawn Mower is pulling to the left or right, consider the following: * Check idler arm pulleys and drive sheaves for mud and/or grass buildup. * Ensure idler arms pivot freely; if not, lubricate idler pivots. * Check for worn drive belts. * Verify proper tire pressure in drive tires (recommended: 12 to 16 psi). Higher pressures (up to 28 psi) may be used in the tire on the side it pulls to.
T
Tara RaySep 5, 2025
How to fix uneven cuts with my Exmark METRO?
- K
  Kelly DavisSep 5, 2025
  To fix uneven cuts with your Exmark Lawn Mower: * Check the drive tire pressure and tire circumference. See 5.1.9. * Ensure blade spacers, axle positions, and front caster spacers are equal on each blade. * Check caster mounting brackets to ensure all bolts are tight. * Check blade tip to tip for straightness, ensuring they are within 3/16" or one blade width from being in line.
K
Kyle DavisSep 8, 2025
What to do if Exmark Lawn Mower blades do not stop when disengaged?
- C
  Cameron ThompsonSep 8, 2025
  If the blades on your Exmark Lawn Mower do not stop when disengaged, check the belt guides to see that they are properly set.