Exmark TURF TRACER X-SERIES

Questions and Answers

L
Lisa PowellAug 15, 2025
How to fix a starter that won't crank on my Exmark TURF TRACER X Lawn Mower?
- M
  Mary ParkerAug 15, 2025
  If the starter on your Exmark Lawn Mower won't crank, try these steps: First, disengage the PTO. Next, make sure the speed control lever is in the neutral lock position. Also, depress the OPC levers. If these steps don't work, the battery may not have a full charge, so charge it. Check the electrical connections for corrosion or looseness; clean the terminals with electrical contact cleaner, apply dielectric grease, and reconnect them. Finally, check the fuse and replace it if it's blown. If the problem persists, the relay or switch may be defective, and you should contact an Authorized Service Dealer.
S
Steven MendozaAug 18, 2025
What to do if my Exmark TURF TRACER X Lawn Mower engine will not start?
- I
  Isabella LopezAug 18, 2025
  If your Exmark Lawn Mower engine won't start, starts hard, or fails to keep running, here's what you can do: First, ensure the fuel tank isn't empty and the fuel shutoff valve is open. Next, check that the throttle is midway between “SLOW” and “FAST,” and the choke is “ON” for a cold engine or “OFF” for a warm one. Replace the fuel filter if it's dirty. Check and correct any faulty or loose electrical connections, cleaning them as needed. Inspect the spark plug wire connection and clean, adjust, or replace the spark plug if necessary. For issues related to dirt, water, or stale fuel in the fuel system or if the MIL illuminates and blinks, it's best to contact an Authorized Service Dealer.
S
Sara ColeAug 22, 2025
Why is my Exmark Lawn Mower vibrating so much?
- J
  James WatersAug 22, 2025
  If your Exmark Lawn Mower is vibrating abnormally, check the following: * Replace any bent or unbalanced cutting blades. * Tighten the blade mounting bolt and the engine mounting bolts. * Also, tighten any loose engine pulley, idler pulley, or blade pulley. If the engine pulley is damaged, the blade spindle is bent, or the belt is damaged, contact an Authorized Service Dealer or install a new belt.
Z
Zachary MillerAug 26, 2025
Why does my Exmark TURF TRACER X engine lose power?
- E
  Erin BradleyAug 26, 2025
  If your Exmark Lawn Mower engine loses power, try the following: Reduce the ground speed if the engine load is excessive. Clean or replace the air cleaner element if it's dirty. Add oil to the crankcase if the oil level is low. Remove any obstructions from the cooling fins and air passages. Clean or replace the fuel cap if the vent hole is plugged. Replace the fuel filter if it's dirty. If the issue persists, contact an Authorized Service Dealer.
W
Whitney WaltersAug 28, 2025
What to do if the blades on my Exmark TURF TRACER X do not rotate?
- E
  Edward LewisAug 28, 2025
  If your Exmark Lawn Mower blades aren't rotating, check the belt tension. Check the belt for damage and replace if necessary. Install the drive belt and check adjusting shafts and belt guides for correct position. Install new deck belt. Install deck pulley and check the idler pulley, idler arm and spring for correct position and function. Replace the spring if broken or missing. If the PTO clutch doesn't engage, contact an Authorized Service Dealer.
D
daypattySep 1, 2025
Why is my Exmark Lawn Mower engine overheating?
- S
  Scott SmithSep 1, 2025
  If your Exmark Lawn Mower is overheating, reduce the ground speed if the engine load is excessive. Add oil to the crankcase if the oil level is low. Remove any obstructions from the cooling fins and air passages.
J
Justin PerezSep 4, 2025
How to stop my Exmark TURF TRACER X from pulling to one side?
- E
  Erik GarrettSep 4, 2025
  If your Exmark Lawn Mower is pulling to the left or right, adjust the tracking by turning the knob on the right hydro control linkage in the direction the mower needs to be adjusted. Turn the knob in 1/4 turn increments until the mower tracks correctly. Also, adjust the tire pressure in the drive tires.
H
hernandezmelissaSep 7, 2025
What to do if my Exmark Lawn Mower does not drive?
- M
  Martha MyersSep 7, 2025
  If your Exmark Lawn Mower isn't driving, tighten the bypass valve. If that doesn't solve the issue, change the belt if the drive or pump belt is worn, loose, or broken. If the drive or pump belt is off a pulley, change the belt.
J
Jose WilliamsSep 12, 2025
How to fix uneven cutting height on my Exmark Lawn Mower?
- H
  Heather BriggsSep 12, 2025
  To address uneven cutting height with your Exmark Lawn Mower, start by sharpening the blades. If the cutting blades are bent, replace them. Ensure the mower deck is level from side-to-side and front-to-rear. Clean the underside of the mower deck. Adjust the tire pressure in the drive tires. For a bent blade spindle or uneven cutting height of adjacent blade tips, contact an Authorized Service Dealer or replace blades, spindles and (or) check for damage to mower deck.

Summary

Introduction

Model and Serial Number Location

Identifies where to find the mower's model and serial numbers.

Safety

Safety Alert Symbol and Levels

Explains the meaning and usage of the safety alert symbol and warning levels.

Safe Operating Practices and Preparation

Outlines essential practices for safe operation, operator training, and pre-operation prep.

Safety

Gasoline Hazards and Precautions

Covers fueling hazards, health risks, and safety measures related to gasoline.

Safety

Slope Operation Safety

Provides crucial safety guidelines for operating the mower on slopes.

Safety

Maintenance and Storage Safety

Outlines safety precautions for maintenance and storage procedures.

Battery Charging Safety

Warns about explosive gases from batteries during charging or jump-starting.

Safety

Hydraulic Fluid Leak Dangers

Details dangers of high-pressure hydraulic fluid leaks.

Safety

Safety and Instructional Decals

Emphasizes maintaining legible safety signs and familiarizing with their meanings.

Specifications

Model, Engine, Fuel, and Electrical Details

Covers model numbers, engine, fuel system, and electrical system specifications.

Safety Interlock & Transmission Systems

Explains safety interlocks and details the hydrostatic transmission system.

Specifications

Tires, Wheels, and Dimensions

Lists tire/wheel specs and machine dimensions for various deck sizes.

Cutting Deck Specifications

Covers deck model numbers, cutting width, blade size, and depth.

Torque Requirements

Product Overview

Operation

Control Levers and Latches

Details OPC levers, drive levers, and neutral lock latches.

Control Functions

Describes throttle, speed control, and brake lever operations.

Operation

Ignition, Fuel Valve, and PTO Controls

Explains ignition, fuel valve, tracking adjustment, and PTO switch operations.

Pre-Start Procedures

Provides essential pre-start checks and fuel recommendations.

Operation

PTO Engagement and Stopping Engine

Provides safety warnings and instructions for PTO engagement/disengagement and engine stopping.

Operation

Driving Forward and Lever Operation

Explains driving forward and lever/latch operation.

Operation

Driving in Reverse and Adjusting Cutting Height

Details reverse driving and step-by-step guide for adjusting cutting height.

Operation

Transporting the Mower Safely

Provides critical safety warnings and procedures for transporting the mower.

Maintenance

Recommended Maintenance Schedule

Presents a detailed schedule for routine maintenance tasks based on service intervals.

Maintenance

Engine Oil and Battery Checks

Step-by-step instructions for checking engine oil and battery charge.

Maintenance

Check Mower Blades

Instructions for inspecting, sharpening, or replacing mower blades.

Maintenance

Check Safety Interlock System

Outlines tests to verify the proper function of safety interlock circuits.

Maintenance

Engine Oil and Hydraulic Oil Checks

Step-by-step guides for changing engine oil and checking hydraulic oil.

Tire Pressure Checks

Details how to check and adjust tire pressures for optimal performance.

Maintenance

Lubricate Grease Fittings and Hubs

Provides chart and instructions for lubricating grease fittings and caster wheel hubs.

Maintenance

Spark Plug and Fuel Filter Service

Instructions for checking spark plugs and changing the fuel filter.

Maintenance

Hydraulic System Filter and Air Purge

Guides for replacing the hydraulic filter and purging air from the system.

Maintenance

Wheel Hub-Slotted Nut Torque Specification

Specifies torque values for wheel hub slotted nuts based on style.

Adjustments

Park Brake and Speed Control Linkage Adjustments

Provides instructions for adjusting the park brake and speed control linkage.

Maintenance

Adjust Hydro Control Linkages

Provides instructions for adjusting hydro control linkages for neutral positioning.

Maintenance

Drive Lever Linkage and Tracking Adjustments

Details adjustments for drive levers and tracking.

Hydro Pump Spring Tension Setting

Describes how to adjust hydro pump spring tension for heavy-duty conditions.

Troubleshooting

Engine Starting and Running Problems

Addresses issues with engine starting and running, providing potential causes and solutions.

Troubleshooting

Engine Overheating and Cutting Issues

Covers engine overheating, uneven cutting, and blade rotation problems.

Schematics

Electrical Diagram - Non-EFI Units

Provides the electrical wiring diagram for non-Kohler EFI units.

Schematics

Electrical Diagram - Kohler EFI Units

Presents the electrical wiring diagram specifically for Kohler EFI units.

Schematics

Electrical Logic Schematic - Non-EFI Units

Shows the logic schematic for electrical systems on non-Kohler EFI units.

Schematics

Electrical Logic Schematic - Kohler EFI Units

Displays the logic schematic for electrical systems on Kohler EFI units.

Schematics

Hydraulic Diagram Overview

Illustrates the hydraulic system of the mower, showing component connections.

Exmark Warranty Information

Warranty Conditions and Service

Details warranty terms, coverage, exclusions, and service procedures.

Exmark Maintenance Fluids

Engine Oil and Hydro Oil Details

Describes the features and benefits of Exmark's premium engine and hydro oils.

Exmark Accessories and Options

Riding and Walk-Behind Accessories

Lists available accessories and options for various mower types.

Exmark TURF TRACER X-SERIES Specifications

General

Deck Type	Floating Deck
Transmission	Hydro-Drive
Fuel Capacity	5 gallons
Cutting Width	52 inches
Deck Material	Steel
Turning Radius	Zero-turn
Engine	Kawasaki FS730V or FX730V