Extron electronics XTP II CrossPoint 1600 User Manual

SIS Command and Response Table for Input-Endpoint-Specific Commands (continued)
Command Function
SIS Command
(Host to Unit to Endpoint)
Response
(Endpoint to Unit to Host)
Additional Description
XTP T USW 103 switcher specific commands (continued)
Audio routing selections
Enable black signal for XTP T
endpoint
E
E
X^
*1AFMT
}
AfmtE
X^
*1
]
Enable an audio only tie for the
connected XTP transmitter.
Disable black signal for XTP T
endpoint
E
E
X^
*0AFMT
}
AfmtE
X^
*0
]
Disable an audio only tie for the
connected XTP transmitter.
View black signal output status for
XTP T endpoint
E
E
X^
*AFMT
} X2#]
The black signal status of XTP
transmitter endpoint
X@
is
X2#
.
Input reports as an HDCP-authorized device
HDCP authorized device on
E
E
X^
*1HDCP
}
HdcpE
X^
*1
]
Set the input as an HDCP authorized
device.
HDCP authorized device off
E
E
X^
*0HDCP
}
HdcpE
X^
*0
]
Set the input as not an HDCP
authorized device.
View HDCP authorized status
E
E
X^
HDCP
} X1#]
Show HDCP authorized device status.
HDCP status
View input HDCP status
E
I
X^
HDCP
} X1$]
View HDCP status of all inputs
E
I*HDCP
} X1$
1
X1$
2
X1$
3
...
X1$
n
]
Input sync detection
View all input connections
0LS
X%
1
X%
2
X%
3
...
X%
n
]
16, 32, or 64 (
n
)
X%
s; each is the
connection status of an input, starting
from input 1.
Example
(XTP II CrossPoint 3200):
0LS
Input:
Response Status:
No input detected
Sync detected Sync detected
1 2345
6
7 8 9
1011
12
13
32
0 0 0 1 1 1 0 1 0 0 1 0 1. . .0
XTP T VGA transmitter specific commands
Input video format
Set format
X^
*
X3)
\ Ityp
X^
*
X3)
*
X3!]
Set input
X^
to
X3)
video format. The
board reports the detected video
format,
X3!
, in the response.
Example:
1*0\
Ityp01*0*5
]
Set input 1 to auto. The board reports
RGB video.
View format
X^
\
X3)
*
X3!]
View set (
X3)
) and detected (
X3!
) video
format of input
X^
.
Image reset
Execute an image reset
X^
A Aadj
X^]
Reset input signal timing to Extron
default for input
X^
.
NOTE: X% = Input signal status 0 = No signal detected 1 = Sync detected
X^ = Input number (for other than tie) 01 – 16, 32, or 64
X1# = HDCP authorized device 0 = Off 1 = On (default)
X1$ = HDCP status (for inputs) 0 = No source device connected
1 = Source connected is HDCP-compliant
2 = Source connected is not HDCP-compliant
X2#
= Enable or disable
0 = Disable 1 = Enable (default)
(for black signal output)
X3) = Input video source 0 = Auto (default)
1 = Video 4 = YUV interlace
2 = S-video 5 = RGB
3 = RGBcvS (SCART) 6 = YUV
X3! = Detected video format 0 = no signal detected
1 = Video 4 = YUV interlace
2 = S-video 5 = RGB
3 = RGBcvS (SCART) 6 = YUV
XTP II CrossPoint 1600, 3200, and 6400 Switchers • Programming Guide 98

Extron electronics XTP II CrossPoint 1600 Specifications

General

Brand	Extron electronics
Model	XTP II CrossPoint 1600
Category	Matrix Switcher
Language	English