Ezviz BC1C User Manual

7
EZVIZ Connect
1. Use Amazon Alexa
These instructions will enable you to control your EZVIZ devices with Amazon
Alexa. If you run into any difficulties during the process, please refer to
Troubleshooting.
Before you start, make sure that:
1. EZVIZ devices are connected to the EZVIZ app.
2. In the EZVIZ app, turn off the "Image Encryption" in the Device Settings page.
3. You have an Alexa-enabled device (i.e Echo Spot, Echo-Show, All-new Echo-
Show, Fire TV (all generations), Fire TV stick (second generation only), or Fire
TV Edition smart TVs).
4. The Amazon Alexa app is already installed on your smart device, and you have
created an account.
To Control EZVIZ devices with Amazon Alexa:
1. Open the Alexa app and select "Skills and Games" from the menu.
2. OntheSkillsandGamesscreen,searchfor"EZVIZ",andyouwillnd"EZVIZ"
skills.
3. Select your EZVIZ device's skill, then tap ENABLE TO USE.
4. Enter your EZVIZ username and password, and tap Sign in.
5. Tap the Authorize button to authorize Alexa to access your EZVIZ account, so
that Alexa can control your EZVIZ devices.
6. You will see "EZVIZ has been successfully linked", then tap DISCOVER DEVICES
to allow Alexa to discover all your EZVIZ devices.
7. Go back to Alexa app menu and select "Devices", and under devices you will
see all your EZVIZ devices.
Voice Command
Discover a new smart device via the "Smart Home" menu in the Alexa app or the
Alexa Voice Control function.
Once the device is found, you can control it with your voice. Speak simple
commands to Alexa.
Your device's name for example: "show xxxx camera," can be modified in the EZVIZ app.
Every time you change the name of the device, you will need to discover the device again
to update the name.
Troubleshooting
What do I do if Alexa fails to discover my device?
Check if there are any Internet connecting problems.
Try to reboot the smart device and re-discover the device on Alexa.
Whydoesthedevice'sstatusshow"Ofine"onAlexa?
Your wireless connection might have been disconnected. Reboot the smart
device and re-discover on Alexa.
Internet access on your router could be unavailable. Check if your router is
connected to the Internet and try again.
For details about countries that support the using of Amazon Alexa, see its official
website.

Ezviz BC1C Specifications

General

Mounting kit	Yes
Number of cameras	1
Type	IP security camera
Operating frequency	2400 - 2483.5 MHz
Placement supported	Outdoor
Connectivity technology	Wireless
Built-in HDD	No
Flash memory	32768 MB
Sustainability certificates	CE, Federal Communications Commission (FCC), REACH, RoHS, UL ECOLOGO, WEEE
Form factor	Bullet
Mounting type	Ceiling/wall
Product color	Black, Grey
Protection features	Dust resistant, Water resistant
International Protection (IP) code	IP66
Security algorithms	64-bit WEP, 128-bit WEP, WPA, WPA-PSK, WPA2, WPA2-PSK
Minimum illumination	0.2 lx
Adjustment shutter speed	Auto
Sensor type	CMOS
Optical sensor size	1/2.8 \
Battery capacity	7800 mAh
DC output current	2 A
DC output voltage	5
Power source type	Battery
Battery technology	Lithium
Operating temperature (T-T)	-20 - 50 °C
Operating relative humidity (H-H)	0 - 95 %
Fixed focal length	2.8 mm
LED type	IR
Night vision distance	10 m
Total megapixels	2 MP
Maximum resolution	1920 x 1080 pixels
Supported video modes	1080p
Video compression formats	H.264, H.265
Noise reduction technology	3D noise reduction
Supported graphics resolutions	1920 x 1080 (HD 1080)
Wi-Fi standards	802.11b, 802.11g, Wi-Fi 4 (802.11n)
Networking standards	IEEE 802.11b, IEEE 802.11g, IEEE 802.11n
Wi-Fi data rate (max)	72 Mbit/s

Weight and Dimensions

Depth	62.8 mm
Width	104.76 mm
Weight	365 g