22
ENGLISH
Table 2:Technical specifications of 960MP Electronic Control
Unit + 961 B-E Programming unit
Power supply 230 Vac (+6 -10%) - 50 (60) Hz
Accessories power supply 24 Vdc / 500 mA max.
Electric lock power supply (N.O./N.C.) 24 Vdc / 0.5 A max.
Standard operating functions (switch) Open / Automatic / Manual
(Night)
Adjustable functions (trimmer) Opening speed - Closing speed
Pulling force - Pause time
Selectable functions (microswitches) Overclosing stroke
Standard/non-standard initialisation procedure
Push and Go - Function switch (pos. “0”)
Terminal strip outputs Door open/closed signal -
Malfunction alarm signal-
24 Vdc electric lock power supply
(N.O./N.C.) - 24 Vdc accessories power supply -
Presence signal (gong) - PC connection signals -
“Interlock” signals - “Double leaf door” signals
Terminal strip inputs Function switch/CODIS (optional) -
Internal / external / emergency /
STOP safety device / CLOSURE safety device
1.1 APPLICATION LIMITS
Important: To ensure correct application of the FAAC 961 B-E
unit the weight of the door must not exceed the value given in
Table 3 corresponding to its length.
The maximum length of the leaf is 1400 mm.
The values of maximum weight vary according to the driving
arm used.
For each driving arm there is also a different maximum value for
the depth of the doorpost (Table 4) beyond which it is not
possible to install the system correctly.
Table 3: Application limits of 961 B-E automatic unit
700 367 286 -
750 320 249 -
800 281 219 -
850 249 194 194
900 222 173 173
950 199 155 155
1000 180 140 140
1050 163 127 127
1100 149 116 116
1150 136 106 106
1200 125 97 97
1250 115 90 90
1300 107 83 83
1350 99 77 77
1400 92 71 71
Table 4: Max. depth of doorpost
mm
FAAC 961 B-E
The 961 B-E automatic unit for swing doors is a one-piece unit
consisting of an electromechanical device that allows door
opening to be controlled by means of a driving arm. The door
is re-closed by a spring system.
The operator can be installed either on the lintel or on the door
structure itself.
The stainless steel protective casing houses the electronic
control unit used to program and control the operation of the
system.
In the event of a power failure the door can be pushed (or
pulled) open manually.
1. DESCRIPTION AND TECHNICAL CHARACTERISTICS
Sliding arm
0 - 125 126 - 250 0 - 160 0 - 160
Pulling
articulated
arm
Pushing
articulated
arm (Var. 02)
Table 1: Technical specifications of 961 B-E Operator
Power supply 230 Vac (+6 -10%) - 50 (60) Hz
Absorbed power 100 W
Current drawn 0.5 A
Electric motor 24 Vdc with encoder
Dimensions 530 x 100 x 104 (length x height x depth)
Weight 10 kg
Ambient temperature -15 +70 °C
Housing protection IP 23
Dimensions and max. weight of leaf see Table 3 (section 1.1)
Duty cycle continuous
Operation in event of power failure Manual push/pull opening -
Spring closure
Configuration of driving arms • pushing articulated arm
(version for jamb depth 0-125 mm)
• pushing articulated arm - (version for jamb depth
126-250 mm) • pulling articulated arm • sliding arm
Anti-crushing device standard
Opening angle 70-95°
Opening time 3.5 - 10 s (adjustable)
Closing time 6 - 13 s (adjustable)
Max. weight of leaf
(kg)
Pulling articulated
arm
Max. weight of leaf
(kg)
Sliding arm
Pushing
articulated
arm (Var. 01)
3
1
2
6
7
13
12
11
10
9
8
5
4
a
Cable hole
b
Support profile
c
960 MP electronic control unit
d
Position monitoring microswitch
e
Spring loading adjustment screw
f
Transmission shaft
g
Drive system
h
DC motor
i
961 B-E programming unit
j
Closing spring
k
Protective casing
l
Operating function switch
m
End cover (2)
Fig. 1
Length of leaf
(mm)
Max. weight of leaf
(kg)
Pushing articulated
arm
To Next Page
Loading...
