4
TAB. 2
B
1
125-134 135-144 145-154 155-164 165-174 175-184 185-194 195-204 205-214 215-224 225-234 235-244 245-254 255-264 265-274
D
1
120-124 110° (1) 110° (1) 115° (1) 108° (1) 100° (1) 100° (1) 108° (2) 100° (2) 100° (2) 100° (3) 100° (3)
125-134
108° (1) 110° (1) 110° (1) 103° (1) 100° (1) 94° (1) 103° (2) 100° (2) 94° (2) 100° (3) 94° (3)
135-144
100° (1) 107° (1) 108° (1) 104° (1) 100° (1) 96° (1) 92° (1) 100° (2) 96° (2) 92° (2) 96° (3) 92° (3)
145-154
100° (1) 105° (1) 106° (1) 100° (1) 96° (1) 90° (1) 100° (2) 96° (2) 90° (2) 96° (3) 90° (3)
155-164
97° (1) 100° (1) 105° (1) 99° (1) 94° (1) 92° (1) 99° (2) 94° (2) 92° (2) 94° (3) 92° (3)
165-174
93° (1) 97° (1) 100° (1) 100° (1) 96° (1) 100° (2) 100° (2) 96° (2) 100° (3) 96° (3)
175-184
90° (1) 95° (1) 100° (1) 96° (1) 95° (2) 100° (2) 96° (2) 100° (3) 96° (3)
185-194
90° (1) 90° (1) 95° (1) 97° (1) 90° (2) 95° (2) 97° (2) 95° (3) 97° (3)
195-204
90° (1) 90° (1) 95° (1) 90° (2) 90° (2) 95° (2) 90° (3) 95° (3)
205-214
90° (1) 90° (1) 90° (2) 90° (2) 90° (2) 90° (3) 90° (3)
215-224
90° (1) 89° (2) 90° (2) 90° (2) 90° (2) 90° (3) 90° (3)
Z
a° (3)
a° (2)
D
1
a° (1)
(3)
(2)
(1)
TAB.2
B
1
XXX XXXX
D
1
XXX 115° (1) 115° (1)
XXX 110° (2) 110° (2)
XXX 100° (3) 100° (3)
B
1
50
75
100
85
1060
B
1
D
1
Z
a
ENGLISH
- INTERSECT THE DIMENSIONS " D
1
" AND " B
1
" TO OBTAIN THE MAXIMUM VALUE OF OPENING GRADES.
- ATTENTION: USE MECHANICAL LIMIT SWITCHES IN ORDER NOT TO EXCEED THE MAXIMUM OPENING GRADES STATED IN TABLE 2 AND GUARANTEE
THE CORRECT OPERATION OF THE AUTOMATED SYSTEM.
HOLE TO BE USED ON THE REAR BRACKET
HOLE TO BE USED
ON THE REAR
BRACKET
INSTALLATION DIMENSION " B
1
"
(SEE FIGURE 4
1
-5
1
)
Dimensions in millimeters
INSTALLATION
DIMENSION " D
1
" (SEE FIGURE 4
1
-5
1
)
Dimensions in millimeters
Fig.5
1
Fig.4
1
3.2.2 APPLICATION WITH BRACKET FASTENED TO SIDE WALL
ATTENTION: do not cut for any reason the rear bracket
Make reference to figures 4
1
and 5
1
and to table 2 to determine the installation position of the operator.
To Next Page
Loading...
