Fagor AD-64CW - User Manual

Questions and Answers

S
Sara KellyAug 18, 2025
Why is my Fagor AD-64CW not cleaning dishes properly?
- M
  melissavaldezAug 18, 2025
  If dishes are not coming out clean enough from your Fagor Dishwasher, consider the following: * Review the proper loading techniques, avoiding overloading. * Inspect the washing and rinsing arms for any blockages or debris and ensure they rotate freely. Clean if necessary. * Check the drain for clogs and remove any obstructions. Ensure the drain hose isn't kinked. * Make sure the dishwasher is level by adjusting the legs.
M
Michele PatrickAug 28, 2025
Why is my Fagor AD-64CW not filling with water?
- M
  Michelle HernandezAug 28, 2025
  If your Fagor Dishwasher isn't filling or reaching the correct water level, and the power light is on, check the following: * Make sure the hose isn't blocked or kinked, the water valve is open, and the pressure is above 20 psi. * Ensure the machine is level by adjusting the legs. * Inspect the overflow tube and O-ring, ensuring they are properly attached and in good condition. * Check the wiring at the door switch for loose connections; if none, replace the switch or the door relay. * Verify voltage at terminal 2 (brown) and GND on the fill pressure switch (P1). If there's no voltage, P1 may be stuck. * Check the wiring and voltage at the rinse/fill valve; replace the fill valve if necessary.
N
Nathan RamirezSep 1, 2025
How to troubleshoot slow filling and weak rinse in Fagor AD-64CW Dishwasher?
- L
  Larry GreenSep 1, 2025
  If your Fagor Dishwasher fills slowly or has a weak rinse, consider these solutions: * Make sure the inlet water pressure is between 20 and 25 psi. * Inspect the hose strainer for clogs. * Disconnect the hose from the fill valve and inspect the filter screen inside for debris. Replace the rinse/fill valve if needed. * Check the temperature with a calibrated thermometer at the temperature sensor location. Replace the temperature gauge if needed.
P
Patricia BrownSep 4, 2025
What to do if Fagor AD-64CW rinse water isn't reaching 180°F?
- D
  Dr. Amanda Davis PhDSep 4, 2025
  If the rinse water in your Fagor Dishwasher isn't reaching 180°F, try these steps: * Check that the rinse temperature probe sensor is properly inserted inside the probe well. Replace the Tc thermostat and/or boiler element and heater relay. Reconnect or replace the temperature sensor if A4 or A5 is displayed. * Reset the high limit stat by pressing the red button. Replace it if necessary. Ensure the heater relay is working correctly and the Tc thermostat is cutting off below 195°F. * Verify voltage at the heater relay coil. If the solenoid isn't closing when receiving voltage, replace the heater relay. * Check the boiler element for continuity; if it's open, replace the heater.
R
robertmyersSep 7, 2025
Why is the wash water in my Fagor Dishwasher not reaching 150°F?
- A
  Amanda PerezSep 7, 2025
  If the wash water in your Fagor Dishwasher isn't reaching 150°F, check the following: * Ensure the incoming water temperature is at least 120°F and the pressure is at least 20 psi. The optimal temperature is 140°F, and the optimal pressure is 25 psi. * Verify that there is power on violet coming from Tc to Tt. Reconnect or replace the temperature sensor if A4 or A5 is displayed. * Verify voltage to the t-stat. If voltage has been verified ok, check tank heater relay Ct. * Verify voltage at the heater relay coil. If the solenoid isn't closing when receiving voltage, replace the heater relay. * Check the tank heater for continuity; if it's open, replace the heater.
R
rogersfeliciaSep 10, 2025
How to fix Fagor AD-64CW that won't turn on?
- B
  Brandon BlairSep 12, 2025
  If your Fagor Dishwasher won't turn on and the power light isn't lit, try the following: * Reset the service breaker. If it trips again, contact an electrician. * Ensure the unit is connected to a live power feed, and verify the voltage and proper phasing. * Make sure power is being supplied to the circuit board. Check for loose wiring and the circuit board fuse. Verify voltage between R (brown) and N (blue). If 208V-240V is found, replace the circuit board.
L
Lori PowellNov 14, 2025
What to do if Fagor AD-64CW Dishwasher washes and rinses but does not drain?
- C
  Crystal RodgersNov 14, 2025
  If your Fagor Dishwasher washes and rinses but doesn't drain, here are some things to check: * Ensure the door is open, and push the drain button for 3 seconds. * Remove the Front Right S/S Filter and the overflow tube. * Inspect the drain pump for clogs by opening the drain pump cover and removing any debris. * Check for kinks in the drain hose and flush out any accumulated debris. * Verify voltage to the drain pump; if it's receiving voltage, replace the drain pump. * Check the safety pressure switch and the black rubber pressure tube for kinks or damage; replace if necessary. * Ensure the sanitized rinsing temperature reaches a minimum of 180ºF, the incoming water temperature is 140°F, and the incoming water pressure is 20-25 psi. * Make sure detergent to dish ratio is ...
H
hannakelseyNov 21, 2025
What to do if Fagor AD-64CW Dishwasher runs continuously in the wash cycle?
- E
  Erik GonzalezNov 21, 2025
  If your Fagor Dishwasher runs continuously or doesn't rinse, check the following: * Ensure power is supplied to the circuit board, check wiring connections and the fuse. Verify voltage between R (brown) and N (blue). If 208V-240V is found, replace the circuit board. * Verify the rinse gauge temperature is above 180°F. If it is, replace the circuit board. If the rinse temperature is below 180°F, replace the Tc thermostat and/or boiler element and heater relay. Reconnect or replace the temperature sensor if A4 or A5 is displayed. * Check the wiring and voltage at the rinse/fill valve; replace the fill valve if necessary. * Make sure the hose isn't blocked or kinked and that the inlet water pressure is between 20 and 25 psi. * Remove and clean any clogged or obstructed rinse arms/n...
D
Dennis BoydNov 23, 2025
What to do if my Fagor Dishwasher will not run?
- P
  Peter WilliamsNov 23, 2025
  If your Fagor Dishwasher won't run after filling and heating, with the power light on, consider these steps: 1. Check the fill pressure switch (P1) to ensure it changes position. 2. Verify the connection between the digital start buttons and the circuit board. Reconnect if disconnected and check the circuit board fuse. Replace the Adhesive Trim if it's still not working. 3. Ensure power is supplied to the circuit board. Check for loose wiring and the circuit board fuse. Verify voltage between R (brown) and N (blue). Replace the circuit board if 208V-240V is found. 4. Rotate the wash pump from the shaft flat head slot counter-clockwise to check for free rotation. Confirm the wash pump is getting power; if so, replace the pump. 5. Wait for the rinsing temperature to reach at least 180º...

Summary

Dishwasher Specifications

AD-48 W Specifications

Detailed performance, capacities, and technical specs for the AD-48W model.

AD-64 CW Specifications

Detailed performance, capacities, and technical specs for the AD-64 CW model.

AD-72 W Specifications

Detailed performance, capacities, and technical specs for the AD-72 W model.

Installation Procedures

Visual Inspection

Instructions for inspecting the unit and packaging for damage before installation.

Installation Diagrams

Visual representations showing clearances, connections, and dimensions for models.

Data Plate and Positioning

Information on the data plate and how to level and position the dishwasher unit.

Water Installation

Water Quality and Drainage

Specifies required water quality and guidelines for water drainage installation.

Electrical Connection

Phase Transformation

Details wiring configurations for transforming phases and connecting power to the unit.

Installation Checklist

Pre-Operation Checklist

A comprehensive list of items to check before operating or servicing the dishwasher.

Operation

Turning Machine On

Step-by-step instructions for powering on the dishwasher unit.

Preparing for Wash Cycle

Guidance on waiting for optimal temperatures before starting a wash cycle.

Washing Cycles Explained

Explanation of available wash cycles and indicator lights.

Draining and Cleaning

Daily Machine Draining

Procedures for daily draining, filter cleaning, and scrap basket maintenance.

Detergent Control

Detergent and Rinse Dispenser Adjustment

Instructions for adjusting and managing detergent and rinse aid dispensing for optimal results.

Ware Preparation

Deliming Procedure

Steps for removing lime and corrosion deposits to maintain optimal dishwasher conditions.

Troubleshooting

Common Issues and Solutions

Lists common symptoms, possible causes, and corrective actions for dishwasher problems.

Electrical Diagrams

AD-48 W Wiring Diagram

Detailed wiring diagram for the AD-48W model, showing component connections.

AD-64 CW; AD-72 W Wiring Diagram

Detailed wiring diagram for AD-64 CW and AD-72 W models.

Wiring Schematics

AD-48 W Schematics Explanation

Explains wiring symbols and provides a schematic for the AD-48W model.

Recommended Spare Parts

Spare Parts Listing

A list of part numbers and descriptions for common replacement components for different models.

Limited Warranty

Warranty Terms and Exclusions

Outlines the terms, conditions, coverage, and exclusions of the product warranty.

Fagor AD-64CW Specifications

General

Type	Freestanding
Number of Programs	6
Number of Wash Temperatures	5
Energy Star Qualified	Yes
Control Type	Electronic
Place Setting Capacity	12
Decibel Rating	49 dB
Noise Level	49 dB
Delay Start	Yes
Child Lock	Yes
Half Load	Yes