EasyManua.ls Logo

Falcon SG1K-1SC - User Manual

Falcon SG1K-1SC
42 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
SC On-line UPS
User’s Manual
Rack / Tower Models
700VA to 3kVA, 120Vac
© 2016 Falcon® Electric, Inc. All rights reserved.
All other brand names and trademarks are the property of their respective owners.
The information stated in this document is subject to change without notice.
Falcon®, Falcon® Electric and UPS logos are registered trademarks of Falcon Electric, Inc.
OM480039 SC1-3KR_T 120V_12-12-16 REV.NR
Proprietary: The information contained herein is proprietary to Falcon Electric, Inc. and
shall not be reproduced or disclosed in whole or in part or used for any reason except
when such user possesses direct, written authorization from Falcon Electric, Inc.
The statements contained herein are based on good faith assumptions and provided for
general information purposes only. These statements do not constitute an offer, promise,
warranty or guarantee of performance. Actual results may vary depending on certain
events or conditions. This document should not be used or relied upon for any purpose
other than that intended by Falcon Electric, Inc.

Table of Contents

Questions and Answers

  • D
    David AllenAug 8, 2025
    What to do if my Falcon UPS has a Fault LED?
    • J
      jessicavangAug 8, 2025
      If the Fault LED is on, read the error code displayed on the LCD to identify the fault. If you see error code Er05 or Er39, check the battery connection and voltage, recharge the batteries for 8 hours if needed, and test the UPS during a simulated outage. For an overload, disconnect non-critical devices until it ceases and inspect cables for short circuits. If the error code is Er11, ensure the ventilation is clear and the fans are working. For site wiring issues, check the AC source wiring and ground-neutral voltage. If the error code is Er14, verify the fans are functioning properly.
  • M
    Mary BarberAug 14, 2025
    Why does my Falcon SG1K-1SC UPS switch between battery and utility mode?
    • A
      Amy PriceAug 14, 2025
      The Falcon UPS may switch between battery and utility modes due to a faulty power strip connected to it. Try removing the power strip. Another cause might be damage to the utility wall receptacle or a faulty cord plug. In this case, replace the wall receptacle or cord plug.
  • G
    Gregory McdanielAug 20, 2025
    What to do if my Falcon SG1K-1SC is unable to provide backup power?
    • A
      Andre SchmidtAug 20, 2025
      If your Falcon UPS fails to provide backup power, first check that the battery connectors are fully engaged. If the batteries are weak, allow them to recharge. If the problem persists after recharging, replace the batteries.
  • P
    Pamela MillerAug 27, 2025
    Why does Falcon SG1K-1SC fail to provide specified battery backup time?
    • A
      amanda73Aug 27, 2025
      If your Falcon UPS does not provide the specified backup time, allow the batteries to charge for 8 hours. If the backup time is still unsatisfactory after charging, contact Falcon Electric for battery replacement.
  • J
    Jacob EllisSep 1, 2025
    What to do if Falcon SG1K-1SC makes strange noise or smell?
    • J
      jacqueline01Sep 1, 2025
      If your Falcon UPS emits a strange noise or smell, immediately shut down the entire system and disconnect the power from the UPS.

Summary

Safety and Storage Instructions

Safety Precautions

Essential safety guidelines for installing, operating, and maintaining the UPS.

UPS Interface and Controls

Front Panel Overview

LCD Panel Details

Rear Panel Connections

Details the ports, connectors, and circuit breakers on the rear of the UPS.

Communication Ports

Information on available communication interfaces like RS-232 and EPO/ROO.

Installation and Location

Installation Procedures

Guides for installing the UPS in either a tower or rack-mount configuration.

Installation Site Requirements

Guidelines for selecting an appropriate and safe location for UPS placement.

Troubleshooting and Maintenance

UPS Beep Codes

Troubleshooting Common Issues

Guidance for diagnosing and resolving UPS malfunctions based on fault conditions.

Error Code References

Explanation and definition of error codes displayed on LED and LCD panels.

Routine Maintenance

Communication and Support

Communication Software Setup

Falcon Electric Service Contact

Falcon SG1K-1SC Specifications

General IconGeneral
Apparent Power1000VA
Real Power600W
TopologyLine Interactive
Frequency50/60Hz
Battery Recharge Time4 hours to 90% capacity
Communication InterfaceUSB
Operating Temperature0°C to 40°C
Operating Humidity0% to 90% non-condensing

Related product manuals