To Next PageTo Next PageWhat to do if Falcon UPS beeps continuously?
If your Falcon UPS emits one long beep every few seconds, this indicates an output overload, charger failure, or a general UPS alarm. Check the LCD display and remove some load from the UPS.
Why does my Falcon SSG3KRM-1 beep 7 times then 3 times?
This beeping pattern on your Falcon UPS indicates that the battery is low after a utility power loss. To resolve this, save your data, turn off the equipment, and wait for the utility power to return.
What to do if Falcon SSG3KRM-1 beeps 6 times?
If your Falcon UPS is beeping six times continuously, it means the PFC over current protection has been activated. Verify that the input AC voltage is not too low and remove some of the load from the UPS output.
What to do if Falcon UPS beeps 5 times?
If your Falcon UPS is beeping five times continuously, it indicates an internal over temperature issue or a cooling fan failure. Check the air vents for any blockage, ensure the fan is operating correctly, and verify the ambient room temperature is within acceptable limits.
Why is my Falcon UPS beeping 3 times?
The Falcon UPS is beeping three times continuously because the utility voltage is out of range. The UPS has switched to battery mode. Check the utility power supply.
Why is my Falcon SSG3KRM-1 beeping 4 times?
The Falcon UPS beeping four times continuously indicates that the utility frequency is out of range, and the UPS is operating in battery mode. Check the utility power frequency.
How to fix a Falcon UPS that will not turn on?
If your Falcon UPS will not turn on, make sure the input switch on the front panel is turned on. Also, verify that the input cable and battery are properly connected to the UPS and battery bank, and that the battery disconnects are in place and turned on.
Why does my Falcon UPS operate from battery when utility power is on?
If your Falcon UPS operates from the battery even when utility power is present, check the utility power protection devices for an open fuse or circuit breaker.
What does it mean when my Falcon UPS beeps 3 times?
If your Falcon UPS is beeping three times continuously, it indicates that the utility voltage is out of range. The UPS is operating in battery mode, so you should check the utility power supply.
What does 4 beeps mean on a Falcon UPS?
If your Falcon UPS is beeping four times continuously, it means that the utility frequency is out of range. As a result, the UPS is in battery mode. Check the utility power frequency.
General| Model | SSG3KRM-1 |
|---|---|
| Category | UPS |
| Capacity | 3000VA / 2700W |
| Frequency | 50/60 Hz |
| Battery Quantity | 6 |
| Battery Type | Sealed Lead Acid |
| Communication Interface | RS-232, USB, SNMP |
Provides basic information about the Falcon SSG Industrial Wide-temperature UPS.
Highlights important features like temperature range, long-life design, and battery options.
Important instructions and warnings for safe installation and maintenance of the UPS.
Specifies ideal environmental conditions for UPS operation and battery life.
Details the function of key internal circuits like input filter, rectifier, and inverter.
Guidelines for visually inspecting the UPS for shipping damage and filing claims.
Lists all cables and accessories included with the UPS models.
Identifies and describes controls and indicators on the UPS front panel.
Details the various ports and connectors located on the rear panels of different UPS models.
Explains the purpose and function of each UPS component.
Explains LCD icons, meter readings, and front panel button functions.
Specifies acceptable ambient temperature, humidity, and airflow for installation.
Step-by-step guide for mounting the UPS into a standard 19-inch equipment rack.
Instructions for installing or replacing battery packs in different UPS models.
Guides the user through the initial power-up and self-test sequence.
Describes Online, Battery, Bypass, and Green modes of UPS operation.
Details RS-232 and USB port functionalities for connectivity.
Explains jumper settings and pin designations for relay card operations.
Critical safety warnings and precautions when working with UPS batteries.
Guidance on battery disposal, recycling, and proper storage for longevity.
Information on battery capacity indicators, voltage by model, and expected service life.
Step-by-step instructions for replacing battery packs in different UPS models.
Lists audible alarm patterns and their corresponding possible causes and solutions.
Provides solutions for common UPS problems like failure to turn on or loss of output.
Explains severe error codes, their causes, and recommended troubleshooting steps.
Provides service contact details, website, and required information for support.
Outlines the terms, exclusions, and limitations of the UPS product warranty.
