FBD 77 Series - User Manual

Other manuals for FBD 77 Series

Installation And Operation Manual42 pages

Service Bulletin2 pages

Questions and Answers

M
Monica HuntSep 7, 2025
What to do if the FBD Beverage Dispenser shows 'Syrup Out' error #011, 012, 013, 014?
- R
  Randall RileySep 7, 2025
  If the FBD Beverage Dispenser displays a 'Syrup Out' error, it indicates that the syrup pressure is less than 45 PSIG (310 kPag), especially for the base syrup in multi-flavor dispensers. Here's what you should do: * Replace the empty BIB (Bag-In-Box). * Ensure the gas line is properly connected to the BIB pump. * Check that the BIB pump is operating correctly. * Make sure the gas tank is not empty. * Verify the syrup shutoff valve at the solution module is turned on. * Confirm that any syrup shutoff valves at the back of the dispenser are not turned off. * Ensure the syrup supply pressure at the dispenser reads 70 PSIG (483 kPag), adjusting the regulator if necessary. * Check that the syrup pressure transducer is connected and working properly.
A
Alexis ThompsonAug 25, 2025
How do I fix 'CO2 Out' on my FBD 77 Series?
- W
  William MarshallAug 25, 2025
  To resolve a 'CO2 Out' error on your FBD Beverage Dispenser, replace or refill the CO2 tank. Make sure that the CO2 shutoff valve at the back of the unit isn’t turned off, and ensure the CO2 pressure transducer is connected and working properly. Finally, check that the CO2 supply pressure at the dispenser is reading 70 PSI, and adjust the regulator if needed, because CO2 pressure may be less than 45 PSI.
R
Richard ParkerAug 25, 2025
What to do if my FBD Beverage Dispenser says 'Water Out'?
- W
  Wanda DayAug 26, 2025
  To fix a 'Water Out' error on your FBD Beverage Dispenser, make sure the water line to the unit is on and the water shutoff at the solution module is turned on. Ensure the CO2 supply line is connected to the water pump and that the pump is not stalled. Verify the CO2 supply pressure at the dispenser is reading 70 PSI, adjusting the regulator if needed. Also, check that the water pressure transducer is connected and working properly, because water pressure may be less than 45 PSI.
T
Terry HolmesSep 15, 2025
What does error #200: Return Temperature Sensor mean on my FBD Beverage Dispenser and how do I fix it?
- D
  Dawn BrownSep 16, 2025
  Error #200 'Return Temperature Sensor' on your FBD Beverage Dispenser indicates that the refrigeration return (suction) temperature sensor is not reading correctly. To fix it: * Ensure the temperature sensor is plugged in. * Replace the sensor if faulty.
J
jessicaramirezSep 23, 2025
What does 'MOTOR FAILURE' mean on my FBD Beverage Dispenser and how can I fix it?
- L
  Larry WallaceSep 23, 2025
  The 'MOTOR FAILURE' message on your FBD Beverage Dispenser indicates that a beater motor is stalled. Run the beater circuit diagnostic sequence to troubleshoot this issue.
S
Susan HernandezSep 12, 2025
What does error #480: Gas #2 - Low Regulated CO2 PSI mean on my FBD Beverage Dispenser and how to fix it?
- G
  Gary RyanSep 12, 2025
  Error #480 'Gas #2 - Low Regulated CO2 PSI' on your FBD Beverage Dispenser means that the regulated CO2 pressure dropped below 50 PSIG (345 kPag). To fix it: * Ensure the CO2 supply is not low. * Check the 'Gas 2' regulator on the header tray and ensure it is set to 60 PSIG (414 kPag).
C
Curtis Bailey Jr.Sep 2, 2025
What does 'Return Temperature Sensor' mean on FBD 77 Series Beverage Dispenser?
- N
  Nicole ThomasSep 2, 2025
  If your FBD Beverage Dispenser displays 'Return Temperature Sensor', ensure the temperature sensor is plugged in. Replace the sensor if faulty, because the refrigeration return (suction) temperature sensor may not be reading correctly.
S
Sarah SanchezSep 2, 2025
What does 'Refrigeration Malfunction' mean on FBD 77 Series?
- S
  Scott DavisSep 3, 2025
  If your FBD Beverage Dispenser displays 'Refrigeration Malfunction', run the fill diagnostic sequence to determine the reason for the failure, because refrigeration pressures may not be in the correct range.
K
Katelyn BrownSep 23, 2025
Why does my FBD Beverage Dispenser say 'CO2 OUT'?
- M
  maciasalisonSep 23, 2025
  The FBD Beverage Dispenser displays 'CO2 OUT' when the CO2 supply is depleted. Restore the CO2 supply to resolve this. The dispenser will automatically restart.
J
josemelendezAug 28, 2025
Why does my FBD 77 Series say 'Compressor Ran Too Long'?
- E
  elizabeth61Aug 29, 2025
  If your FBD Beverage Dispenser shows 'Compressor Ran Too Long', and the location is an extreme volume venue such as a festival, contact FBD service for instructions on adjusting the timer. Otherwise, run the refrigeration diagnostic sequence to determine the reason for the failure, because the compressor may have run continuously for more than 90 minutes.