What to do if my FBD 77 Series Beverage Dispenser displays 'Board Failure'?
If your FBD Beverage Dispenser is showing a 'Board Failure', cycle the power to the unit to see if it will clear the error. If not, replace the control board, because the control board may not be functioning properly.
How to diagnose 'Motor Failure' in FBD Beverage Dispenser?
To resolve a 'Motor Failure' on your FBD Beverage Dispenser, run a beater circuit diagnostic to determine the problem or refer to error #58X in this manual. Check to make sure the beater motor is plugged in, because the beater motor may not be operating.
Why does my FBD 77 Series say 'Compressor Ran Too Long'?
If your FBD Beverage Dispenser shows 'Compressor Ran Too Long', and the location is an extreme volume venue such as a festival, contact FBD service for instructions on adjusting the timer. Otherwise, run the refrigeration diagnostic sequence to determine the reason for the failure, because the compressor may have run continuously for more than 90 minutes.
What to do if my FBD Beverage Dispenser displays Error #111, 112, 113, 114: Motor Failure?
If your FBD Beverage Dispenser displays Error #111, 112, 113, 114 indicating 'Motor Failure', it means the beater motor is not operating. To solve this: * Run a beater circuit diagnostic to determine the problem or refer to error #58X in this manual. * Check to make sure the beater motor is plugged in.
What does error #200: Return Temperature Sensor mean on my FBD Beverage Dispenser and how do I fix it?
Error #200 'Return Temperature Sensor' on your FBD Beverage Dispenser indicates that the refrigeration return (suction) temperature sensor is not reading correctly. To fix it: * Ensure the temperature sensor is plugged in. * Replace the sensor if faulty.
Why does my FBD Beverage Dispenser say 'CO2 OUT'?
The FBD Beverage Dispenser displays 'CO2 OUT' when the CO2 supply is depleted. Restore the CO2 supply to resolve this. The dispenser will automatically restart.
What to do for 'High regulated CO2 PSI' on FBD Beverage Dispenser?
If your FBD Beverage Dispenser displays a 'High regulated CO2 PSI' error, check the “carbonation” regulator on the header tray and ensure it is set to 60 PSI, because regulated CO2 pressure may be above 70 PSI.
How to fix 'Low regulated CO2 PSI' on FBD Beverage Dispenser?
If you encounter a 'Low regulated CO2 PSI' error on your FBD Beverage Dispenser, make sure the CO2 supply is not low. Check the “carbonation” regulator on the header tray and ensure it is set to 60 PSI, because the regulated CO2 pressure may have dropped below 50 PSI.
How to resolve 'High Barrel Pressure' on FBD 77 Series?
To troubleshoot a 'High Barrel Pressure' error on your FBD Beverage Dispenser, dispense a drink to reduce the barrel pressure. If set to the ON mode, the unit will refreeze. Run the fill diagnostic if a failed component is suspected. Check the “Active Charge” regulator located on the product header to ensure it is set at 30 PSI. Make sure all barrels should be fully depressurized before checking the active charge, because pressure on a barrel may have exceeded 55 PSI.
What to do if my FBD Beverage Dispenser says 'Water Out'?
To fix a 'Water Out' error on your FBD Beverage Dispenser, make sure the water line to the unit is on and the water shutoff at the solution module is turned on. Ensure the CO2 supply line is connected to the water pump and that the pump is not stalled. Verify the CO2 supply pressure at the dispenser is reading 70 PSI, adjusting the regulator if needed. Also, check that the water pressure transducer is connected and working properly, because water pressure may be less than 45 PSI.
Covers electrical, gas, and general safety guidelines for operating the dispenser safely.
Details general, electrical, and dimensional specifications for the 77X series dispensers.
Guides on inspecting, unpacking, and selecting an appropriate installation site.
Instructions for connecting electrical power, water, gas, and syrup supplies.
Covers leak checks, priming, power-up, calibration, and filling barrels.
Explains operating modes and how to adjust drink characteristics for optimal taste.
Covers keypad use, menu structure, accessing information, and configuring settings/schedules.
Guides on remote monitoring, diagnostics, and other advanced features.
Detailed instructions for keeping the dispenser clean and sanitary.
Recommended annual tasks for maintaining dispenser performance.
Guides on interpreting messages, error codes, and resolving common issues.
Provides diagrams for physical mounting, and product/utility flow paths.
Shows electrical connections for different dispenser models.
Depicts refrigeration system layouts for various configurations.
Provides FBD technical support contact details.
General| Brand | FBD |
|---|---|
| Model | 77 Series |
| Category | Beverage Dispenser |
| Language | English |
To Next Page
