FE PXR4 - Index

81
Index
A
B
P
R
C
D
E
H
I
K
L
M
O
S
T
U
Adjusting the PV display (0%)..................................................... 66
Adjusting the PV display (100%)................................................. 66
Alarm codes.................................................................................. 47
Alarm types .................................................................................. 46
Anti-reset windup ......................................................................... 30
Auto-tuning function .................................................................... 20
Basic operations ........................................................................... 12
Calibrating the input ..................................................................... 66
Canceling the alarm latch ............................................................. 19
Cold junction compensation ......................................................... 65
Communication protocol setting .................................................. 72
Contact output .............................................................................. 37
Control algorithm ......................................................................... 31
Cooling side proportional band shift ............................................ 29
Cooling side proportional coefficient ........................................... 28
Current detector input................................................................... 57
Cycle time of control output 1...................................................... 37
Cycle time of control output 2 (Cooling-side) ............................. 38
Dead band ..................................................................................... 29
Decimal point position ................................................................. 42
De-energized output alarm ........................................................... 60
Derivative time ............................................................................. 26
DI1 operation setting .................................................................... 67
Direct action ................................................................................. 53
Displaying On-delay alarm or the remaining time of timers........ 21
Displaying the current input value ............................................... 57
Displaying the output value.......................................................... 64
Dual output ................................................................................... 28
Error display alarm ....................................................................... 60
HB (Set value of heater break alarm) ........................................... 57
HYS (Hysteresis) mode at ON/OFF control ................................ 36
Hysteresis alarm 1, 2 and 3 .......................................................... 59
Hysteresis operation ..................................................................... 36
Hysteresis range for ON/OFF control .......................................... 27
Input signal code .......................................................................... 39
Integral time ................................................................................. 25
Key lock........................................................................................ 23
Local/romote operation setting..................................................... 17
Low PV type................................................................................. 20
Lower limit alarm ......................................................................... 47
Lower limit of alarm 1, 2 and 3 .................................................... 22
Method of setting the SV (setting value)...................................... 14
Manual mode setting .................................................................... 15
ON/OFF control (two-position control) ....................................... 24
Operation methods ....................................................................... 7
Options of alarm 1, 2 and 3 .......................................................... 60
Output direction at input burn-out ................................................ 53
Output limit types ......................................................................... 63
Output offset value ....................................................................... 30
Overlap band ................................................................................ 29
Parameter display mask ................................................................ 78
Parameter functions and method of settings................................. 14
Parameter list ................................................................................ 7
Parity for communication ............................................................. 71
Part names and functions .............................................................. 6
Power-on start ............................................................................... 51
Proportional band ......................................................................... 24
PV (Measured value) offset .......................................................... 43
PV (Measured value) stable range................................................ 35
Ramp-soak control ....................................................................... 18
Ramp-soak modes ........................................................................ 50
Ramp-soak status display ............................................................. 50
Range alarm.................................................................................. 47
RCJ (Cold junction compensation) .............................................. 65
Remote SV input .......................................................................... 75
Remote SV input filter constant ................................................... 76
Remote SV input value display .................................................... 77
Re-transmission base scale ........................................................... 74
Re-transmission output type setting ............................................. 73
Re-transmission span scale........................................................... 74
Reverse action .............................................................................. 53
Selecting ramp-soak patterns........................................................ 49
Selection °C / °F ........................................................................... 40
Self-tuning .................................................................................... 32
Setting alarm 1, 2 and 3 ................................................................ 22
Setting the measuring range (Input range) ................................... 40
Setting the ramp segment time ..................................................... 50
Setting the soak segment time ...................................................... 50
Specifying control action and output direction at input
burn-out .................................................................... 53
Standby settings............................................................................ 16
Station No. for communication .................................................... 70
SV (Setting value) lower limiter................................................... 54
SV (Setting value) offset .............................................................. 44
SV (Setting value) upper limiter .................................................. 54
Switching the parameters ............................................................. 12
The time of ON-delay alarm or timer function ............................ 55
Time constant of input filter ......................................................... 45
Timer code .................................................................................... 47
Troubleshooting............................................................................ 79
Upper and lower limits for control output 1 ................................. 62
Upper and lower limits for control output 2 ................................. 62
Upper limit alarm ......................................................................... 47
Upper limit of alarm 1, 2 and 3 .................................................... 22
User settings ................................................................................. 66
www. .com
information@itm.com1.800.561.8187