Finelite HP-2 User Manual

Patent Pending Note: All power connections to be installed to local/national codes by a Certified Electrician. Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • (510) 441-1100 • Fax: (510) 441-1510 • www.finelite.com
1 of 13
© 2018 FINELITE, INC. ALL RIGHTS RESERVED. Form CE - 98532. 03/18
HP-2 / HP-4 / HP-6 Recessed or Regressed Spackle & Visible Flange Mitered Corner
Installation Instructions
Overview
Step 5
Joining Luminaires
Page 8
Step 1
Rough-Ins & Mounting Options
Pages 2-3
Step 2
Identification & Preparation
Page 4
Step 9
Closing Luminaires
Pages 12-13
Step 4
Mounting Starter
to Structure
Pages 6-7
Step 3
Opening Luminaires
Pages 5
Step 6
Securing Luminaire Joints
Page 9
Step 7
Joining Mitered Corners
Page 10
Step 8
Securing Corners Joints
Page 11
• This installation requires proper support as each luminaire is being installed.
• DO NOT attempt to join luminaires together on the floor. Damage may result
when lifted. Follow these instructions.
NOTE
This is a hypothetical build to show the capabilities of this luminaire family and mount type. Your build may vary.
Helpful Video
0-10V Dimming

Finelite HP-2 Specifications

General

Manufacturer	Finelite
Category	Lighting Equipment
Light Distribution	Direct/Indirect
Voltage	120-277V
Diffuser Material	Acrylic
Color Temperature	3500K
Dimming	0-10V
Lumens	Varies based on length and configuration

Summary

Step 1 - Rough-Ins & Mounting Options

Total Run Length

Details luminaire section length and total run length dimensions.

Rough-In Widths

Specifies rough-in width for Spackle and Visible Flange types.

Rough-In Lengths

Lists total run rough-in lengths for different luminaire models.

Mounting Options for Step 1

Option 1 - Mount to Threaded Rod

Details mounting the luminaire using a 1/4"-20 threaded rod.

Option 2 - Mount to Structure

Details mounting the luminaire directly to structural support.

Step 2 - Identification & Preparation

Identify Luminaires

Instructions for identifying luminaires using ID labels and arranging them.

Remove Diffuser

Guidance on carefully removing and setting aside diffusers while keeping them identifiable.

Step 3 - Opening Luminaires

Release Backplates

Methods for releasing backplates for access to mounting points using tools.

Step 4 - Mounting Starter to Structure

Make Electrical Connections

Details on wiring conduit plates and splice box options for power connection.

Mount Starter to Structure for Step 4

Option 1 - Mount to Threaded Rod

Procedure for mounting the starter luminaire via threaded rod.

Option 2 - Mount to Structure

Procedure for mounting the starter luminaire to structural support.

Step 5 - Joining Luminaires

Mount Joiner/Ender to Structure

Instructions for mounting joiner/ender units to the structure.

Join Luminaires

Steps to align and connect joiner luminaires using aligner sleeves.

Step 6 - Securing Luminaire Joints

Secure Joint with Yoke Brackets

How to attach yoke brackets to secure luminaire joints.

Make Electrical Connections

Connecting plug-together wiring for the joined luminaires.

Step 7 - Joining Mitered Corners

Mount Ender to Structure

Procedure to mount the ender unit to the ceiling structure.

Join Mitered Luminaires

Aligning and sliding the ender with the joiner using aligner sleeves.

Secure Ender to Structure

Fastening the ender unit to the structure after joining.

Step 8 - Securing Corner Joints

Close All Backplates with Yoke Brackets

Securing corner joints by closing backplates with yoke brackets.

Make Electrical Connections

Connecting plug-together wiring for secured corner joints.

Step 9 - Closing Luminaires

Close All Backplates

Reinstalling backplates by snapping them into clips.

Secure Flange To Structure Spackle Flange Only

Securing spackle flanges to wall/ceiling per building codes.

Apply Spackle Spackle Flange Only

Applying spackle and paint over flanges, using mud guards.

Final Step of Step 9 - Replace Diffusers

Replace Diffusers

Installing correct diffusers to their corresponding luminaires and powering on.