How to prevent foam in tank and air entrainment in Finn HydroSeeder T30?
To address foam in the tank and air entrainment in your Finn Farm Equipment, take these steps: * As the slurry level decreases, reduce the agitator speed. * Add 2 to 3 oz (59 to 89 ml) of an anti-foaming agent to the tank. * If you identify an additive causing the issue, add it last, avoid it altogether (unless it's water). * Minimize recirculation time.
Why is my Finn Seeders foaming and not spraying far?
The foaming of the solution and lack of distance in Finn Seeders can be due to several reasons. It could be that the machine is sucking air through the suction line, so check all suction connections and ensure rubber seals are in good shape, greasing them before replacing clamps. Other potential causes include air entrainment, low engine RPM (below 2,750 RPM – No load) which requires checking the throttle cable and linkage, soft water, too much agitation (slow the agitator), a worn pump (reset pump tolerance), a partially plugged suction (clean out machine), a worn or plugged nozzle (clean or replace nozzles), the type of fertilizer being used (change type), or clutch slippage (replace clutch).
What to do if my Finn Seeders pump is having problems?
Several factors can cause pump issues in Finn Seeders. Using fertilizer with highly abrasive fillers, you should change the fertilizer and avoid abrasive fillers. Other causes include overloading the machine with dry material (load to recommended capacities), allowing too much time between loading and discharging (set agitator at 1/2 speed in reverse and disengage pump after loading and mixing), recirculating all the time (close recirculation valve when discharging through the boom), the pump being frozen (warm housing to melt ice), the pump being jammed with fertilizer or lime (remove cover and clean interior), or the impeller rusted to the suction cover plate (pull cover and remove rust).
Why is my Finn Seeders leaking?
Leaks in Finn Seeders can stem from several causes. These include a lack of lubrication causing a worn seal (replace seal and follow lube schedule), bolts not tightened (tighten uniformly to 25 lb–ft (34 N•m)), a rubber seal that is cracked, pinched, torn, or missing (replace, always grease seal before clamping shut), a pressure lubricator not serviced (replace pump seal and service automatic pressure lubricator daily), a bad O-ring (replace O-ring; use grease when replacing), or a worn or missing gasket (replace gasket).
What causes the Finn Seeders machine to jump during operation?
The Finn Seeders machine jumping during operation can be attributed to a couple of reasons: the agitator being bent by a heavy object falling on it (straighten agitator shaft or shim so it runs true) or loading wood fiber mulch into the tank before the tank is half full (straighten agitator paddle; realign agitator to run true).
What causes valve problems in Finn Seeders?
Valve problems in Finn Seeders can arise from several causes: the valve being frozen (thaw out ice and lubricate; leave in open position during storage), foreign material in the slurry (drain and clean out tank; check storage for foreign materials), loading HydroSeeder® before the tank is half full of water (reinstruct your operator), incorrect loading procedure, improper operation by the operator, clutch slipping (replace clutch), not opening the valve handle all the way (valve should be fully open), the machine not being flushed out prior to reloading, or the machine not being run at the correct RPM during loading (reinstruct your operator).
How to deal with foam in the tank and air entrainment in Finn Seeders?
To address foam in the tank and air entrainment in Finn Seeders, you can try the following: as the slurry level drops in the tank, slow the agitator; add 2 to 3 oz (59 to 89 ml) of an anti-foaming agent to the tank; and limit recirculation time as much as possible.
What to do if Finn HydroSeeder T30 has plugging or clogging?
If your Finn Farm Equipment experiences plugging or clogging, follow these steps: 1. Disengage the pump clutch and shut down the engine. 2. Remove and clean the discharge nozzle using a cleaning rod to push out any buildup. 3. If the recirculation system isn't working, disengage the pump clutch and shut down the engine. Remove the recirculation valve clamps, slide back the rubber seals, and remove the valve assembly. Inspect the valve assembly, recirculation nozzle, and pipe for obstructions. Clear any blockages, then replace the valve assembly and clamps, lubricating the seals with sodium-based grease. 4. If there is a drop in pressure accompanied by a frothy discharge stream, blockage is in suction line or sump area. Disengage the pump clutch and shut down the engine, then loosen su...
What to do if my Finn Seeders is plugging or clogging?
If your Finn Seeders is experiencing plugging or clogging, several steps can be taken to resolve the issue. If the cause is foreign objects or dewatered mulch, disengage the pump clutch, shut down the engine, remove, and clean the discharge nozzle using a cleaning rod until completely cleared. If the recirculation system isn't working, disengage the pump clutch, shut down the engine, remove the recirculation valve, check for obstructions in the valve assembly, recirculation nozzle, and pipe, clear any blockages, then replace the valve assembly, lubricating the seals. If there is an obstruction in the pump (identified by a pressure drop), disengage the pump clutch, shut down the engine, perform lockout/tagout procedures, loosen suction pipe clamps, and remove any obstruction from the pump. ...
Steps to activate the Finn Limited Warranty and obtain service.
Procedures for reporting issues and getting warranty work done.
Details Finn's warranty coverage, exclusions, and limitations.
Specifies warranty period, storage, and disclaimer information.
Explains hazard alert symbols used in operation and maintenance.
Alerts to state-specific warnings regarding chemicals and exhaust.
Critical checks before starting the HydroSeeder® engine for safety.
Safe operating practices and precautions for using the HydroSeeder®.
Safety guidelines for applying slurry with the HydroSeeder®.
Safety precautions before performing maintenance on the unit.
Decals indicating primary hazards like electrical, arc flash, and burn hazards.
Decals related to operational actions and required protective equipment.
Warnings for confined spaces, flying materials, and hydraulic fluid.
Decals providing specific operational guidance and warnings.
Explains hydroseeding and the HydroSeeder®'s operation.
Specifies requirements for the truck or trailer used to transport the HydroSeeder®.
Guidelines for securely mounting the HydroSeeder® to a vehicle.
Details available optional attachments like discharge hoses and hose reels.
Safety checks to ensure operator safety before starting.
Procedures for checking the equipment's condition before operation.
Explains the operation of the recirculation, discharge, and remote valves.
Illustrates the control box and explains the function of its icons.
Step-by-step instructions for starting the HydroSeeder® engine.
Information on calculating coverage rates based on material and capacity.
Chart showing tank capacity in gallons and corresponding liquid levels.
Steps for loading water and materials into the HydroSeeder® tank.
Procedures for loading and mixing specific viscous slurry types.
Operator familiarization with the area and communication plan.
Guide to choosing the appropriate nozzle based on distance and width.
Techniques for uniform slurry application, nozzle aim, and movement.
Best practices for using discharge hoses with the HydroSeeder®.
Steps to follow after completing a load and before starting the next.
Steps for daily cleaning of the HydroSeeder® unit and its components.
Lubrication points and schedule for daily maintenance.
Instructions for preparing the HydroSeeder® for seasonal or winter storage.
Chart detailing lubricants, fluids, and their usage frequency.
Exploded view and part list for the clump assembly.
Information on the hydraulic system, oil, filtration, and relief settings.
Procedures for maintaining the pump, including tolerances and cleaning.
Solutions for issues related to foam, air entrainment, and reduced spray distance.
Steps to diagnose and clear blockages in the slurry system.
Causes and solutions for leaks in various components.
Addresses problems with machine movement and agitator function.
Solutions for stuck valves, clutch slippage, and engagement issues.
Addresses pump wear, freezing, and impeller-related problems.
Part numbers and descriptions for piping components.
List of parts for the diesel engine clump assembly.
List of parts for the gasoline engine clump assembly.
Part numbers and descriptions for hydraulic system components.
List of parts for the hose reel assembly.
List of parts for the gasoline hydraulic pump drive assembly.
List of parts for the hydraulic agitator drive assembly.
List of parts for agitator and bearing assemblies.
List of miscellaneous loose parts for the HydroSeeder®.
List of specific parts for the gasoline engine.
List of specific parts for the diesel engine.
Parts list for the control box and wiring harness of diesel units.
Electrical schematic for diesel powered HydroSeeder® units.
Parts list for the control box and wiring harness of gasoline units.
Electrical schematic for gasoline powered HydroSeeder® units.
List of items included in the standard tool kit.
Kits available for sealing hydraulic components.
List of various decals indicating hazards and operational instructions.
Information on decal kits available for the HydroSeeder®.
General| Working Capacity | 300 gallons |
|---|---|
| Pump Type | Centrifugal |
| Agitation | Mechanical |
| Hose Length | 50 ft |
| Weight | 575 lbs |
To Next Page
