4195KA, KB, and KC Series
6–4
Key Description Part Number
59 Hex reducing nipple, 1/2–inch NPT male
(Use only when specified)
All ranges up to 0-5000 psig (0-345 bar)
Steel 16A6992 X012
SST 16A6992 X022
0-5000 psig (0-345 bar) to
0-20000 psig (0-1379 bar)
S31600 (316 SST) 16A6996 X012
60 Reducing adaptor,
1/2–inch NPT female
(Use only when specified)
All ranges up to 0-5000 psig (0-345 bar)
Steel 16A6993 X012
SST 16A6993 X022
0-5000 psig (0-345 bar) to
0-15000 psig (0-1034 bar)
S31600 (316 SST) 16A6997 X012
61 Process scale, aluminum
For indicator ass’y (key 101) See Key 61 table
62 Remote set pt ass’y (suffix letter M)
The part numbers listed for key 62 are for the complete remote set
point (suffix letter M) ass’y. Individual assembly parts are listed in
the Remote Set Point Assembly subsection of the parts list. Key
numbers for individual ass’y parts also appear in figure 5–30.
Remote set pt ass’y (suffix letter M)
N09902 (Nickel Alloy, Ni–Span C, Alloy 902)
12 psig (0.8 bar) span 36A6988 X032
24 psig (1.7 bar) span 36A6988 X042
SST
12 psig (0.8 bar) span 36A6988 X012
24 psig (1.7 bar) span 36A6988 X022
64 Machine screw, fill hd, S18800 (18–8 SST)
4 req’d to attach process and set pt
indicator ass’y (key 56) to frame 1J8415 X0012
65 Feedback link ass’y, aluminum/brass/SST 16A7036 X012
71 Machine screw, fill hd, S18800 (18–8 SST)
For all 4195KA, KB Series (4 req’d) 1P4743 X0012
For all 4195KC Series (6 req’d) 1P4743 X0012
72 Blowout plug, silicone
2V7660 05312
Note
Key numbers 73 through 76 are only for use with
a 4195K Series controller with a Bourdon tube
element. Travel stops are required when the cal-
ibration starting point is greater than 0 psig. Use
only when specified.
73 Upper travel stop, G10100 (steel)
Use only when specified. See Note above. 26A9768 X012
74 Lower travel stop, G10100 (steel)
Use only when specified. See Note above. 27B0400 X012
75 Machine screw, fill hd, S18800 (18–8 SST)
Use only when specified. See Note above.
If only upper travel stop installed, none req’d – – –
If both upper and lower travel stop installed,
2 req’d to mount upper travel stop
1H2676 X0012
76 Machine screw, fill hd, S18800 (18–8 SST)
Use only when specified. See Note above.
If only upper travel stop installed,
2 req’d to mount upper travel stop
1V4130 38982
If both upper and lower travel stop installed,
2 req’d to mount lower travel stop
1V4130 38982
Key 61. Process Scale, Positive Pressure
Scale Range Part Number
0 to 60 inch wc
0 to 5
0 to 10
3 to 15
0 to 15
1R0003 X0202
1R0003 X0212
1R0003 X0222
1R0003 X0172
1R0003 X0232
Psig Scales
0 to 20
6 to 30
0 to 30
0 to 60
0 to 100
1R0003 X0242
1R0003 X0182
1R0003 X0032
1R0003 X0042
1R0003 X0052
0 to 200
0 to 300
0 to 600
0 to 1000
0 to 1500
1R0003 X0062
1R0003 X0072
1R0003 X0082
1R0003 X0092
1R0003 X0102
0 to 3000
0 to 5000
0 to 8000
0 to 10,000
1R0003 X01
12
1R0003 X0122
1R0003 X0132
1R0003 X0142
0 to 150 mbar
0 to 400 mbar
0 to 0.6
0 to 1
1R0003 X1562
1R0003 X0422
1R0003 X0402
1R0003 X0432
0.2 to 1
0 to 1.4
0 to 1.6
0 to 2
0.4 to 2
1R0003 X1602
1R0003 X1612
1R0003 X0442
1R0003 X1652
1R0003 X1622
Bar Scales
0 to 2.5
0 to 4
0 to 6
0 to 10
0 to 16
1R0003 X0452
1R0003 X0462
1R0003 X0472
1R0003 X0482
1R0003 X0492
0 to 25
0 to 40
0 to 60
0 to 100
0 to 160
1R0003 X0572
1R0003 X0502
1R0003 X0512
1R0003 X0522
1R0003 X0532
0 to 250
0 to 300
0 to 600
1R0003 X0542
1R0003 X1802
1R0003 X0552
0 to 200
0 to 400
0 to 700
0 to 1400
0 to 2000
1R0003 X0922
1R0003 X0932
1R0003 X0942
1R0003 X0702
1R0003 X0952
kPa Scales
0 to 4000
0 to 7000
0 to 10,000
0 to 20,000
0 to 35,000
1R0003 X0962
1R0003 X0972
1R0003 X0712
1R0003 X0982
1R0003 X0992
0 to 55,000
0 to 70,000
1R0003 X1002
1R0003 X1012
Key 61. Process Scale, All Controllers
Scale Range Part Number
0 to 100%
0 to 10 Square Root
0 to 100 Square Root
1R0003 X1042
1R0003 X1172
1R0003 X1292
Key Description Part Number
120 Machine screw, fill hd, S18800 (18–8 SST)
2 req’d to attach remote set pt ass’y (suffix
letter M) to indicator ass’y base plate 1J8415 X0012
To Next Page
Loading...
