4195KA, KB, and KC Series
6–1
Section 6
Parts
Parts Ordering
Whenever corresponding with your Fisher Controls
sales office or representative about this equipment,
always mention the controller serial number. When
ordering replacement parts, refer to the 11-character
part number of each required part as found in the fol-
lowing parts list.
Parts Kits
Key Description Part Number
4190 Series Auto/Manual Repair Kit
Contains keys 277, 278, 279, 281, 292,
293, 294, 298, 306, 312 R4190X0AM12
4190 Series Auto/Manual Retrofit Kit
Contains keys 138, 273, 312, 313, 314, 315, 316
Brass tubing R4190X00B12
SST tubing R4190X00S12
4190 Series Case Handle Kit
Contains lever and mounting hardware R4190X00H12
4190 Series Controller Repair Kit
Contains keys 4, 5, 7, 8, 24, 52 R4190X00C12
4190 Series Pointer and Bracket Repair Kit
Contains pointer and bracket ass’y,
three machine screws, three washers R4190X00P12
4190 Series Type 83U Relay Repair Kit
Contains keys 5, 6, 7, 8, 11, 13, 14, 15, 19 R83LX000012
Type 4195KBF and 4195KCF Anti–Reset Windup
Retrofit Kits, Contains keys 44, 55
Brass tubing
4195KBF R4190X00B22
4195KCF R4190CX0B22
SST tubing
4195KBF R4190X00S22
Parts List
Abbreviations Used In Parts List
adj: adjustment
alt desgntn: alternative designation
ass’y: assembly
conn(s): connection(s)
diff: differential (as in process differential pressure)
fdback: feedback
fill hd: fillister head (as in fillister head cap screw)
ext: external
hd: head (as in machine screw head)
int: internal
OD: outside diameter
p/o part of (as in part of another assembly)
pl: plated (as in plated steel)
pt: point (as in set point)
qty: quantity
SST: stainless steel
w/: with
w/o: without
Key Description Part Number
Controller Common Parts (figure 5–24)
Note
Figure 5–24 shows key numbers for the
common construction of all controller
types. Figure 5–24 continues over sever-
al pages. Be sure to check all pages of
Figure 5–24 to find the common key
numbers. This figure begins after the
Maintenance section of this manual.
1 Case and cover ass’y
For use w/ or w/o int set pt and
w/o remote or ext set pt 46A5903 X012
For use w/remote set pt and w/o
int or ext set pt 46A5902 X012
For use w/ext set pt and w/o
remote or int set pt 46A5900 X012
2 Nameplate, A91100 (aluminum) - - -
3 Frame, A03600 (aluminum) 56A7001 X012
4* Frame gasket, neoprene
For use between frame and frame
manifold (key 135) 18A0749 X012
5* Gasket, neoprene
4195KA and 4195KB (1 req’d) 18A0742 X012
4195KC (2 req’d)
18A0742 X012
6 Machine screw, fill hd S18800 (18–8 SST)
2 req’d to mount the prop band ind cover
to the frame 1P4373 X0012
4 req’d to mount bellows bracket
(key 31) to bellows beam (key 49) 1P4373 X0012
2 req’d to attach process scale
brackets (keys 376, 377) to frame 1P4373 X0012
7* O–Ring, nitrile
Used between frame and case at conns: process
pressure, either 1/4-18 NPT female or 1/2-14
NPT male; output and supply; remote set point;
and external feedback
3 req’d w/o remote set pt and
w/o ext fdback
1C3762 06992
4 req’d w/remote set pt or ext fdback
1C3762 06992
5 req’d w/remote set pt and ext fdback
1C3762 06992
8* O-Ring, nitrile
Used between frame and case on
mounting bosses extending from the frame
through the back of the case (3 req’d) 16A6903 X012
9 Flexure pivot ass’y, sapphire/SST 29A4340 X012
10 Machine screw, fill hd, S18800 (18–8 SST)
Used to attach the flexure pivot ass’y
(key 9) to the frame (4 req’d) 14A7797 X022
11* Flapper ass’y 29A9518 X012
12 Cap screw, hex socket S18800 (18–8 SST)
For flapper ass’y (key 11) (2 req’d) 10B0700 X012
17 Adjustable set pt pivot ass’y, SST 19A1121 X012
18 Relay nozzle tubing ass’y, SST 18A0765 X012
19 Machine screw, fill hd, S18800 (18–8 SST)
1 req’d to attach adjustable set pt pivot
ass’y (key 17) to frame
1C8990 X0012
1 req’d to attach relay nozzle tubing
ass’y (key 18) to frame
1C8990 X0012
20 Plain washer, S18800 (18-8 SST)
Used w/key 19 (2 req’d)
1K2610 28992
*Recommended spare parts
To Next Page
Loading...
