Type 4660
14
Key Description Part Number
––– Set Point Indicator (Includes set
point assembly and adjustment key)
High Set Point
Bourdon Tube Rating (cont’d)
1500 psig (103.4 bar) R4660X SP1E2
2500 psig (172.4 bar) R4660X SP1F2
5000 psig (344.8 bar) R4660X SP1G2
7500 psig (517.1 bar) R4660X SP1H2
10,000 psig (689.5 bar) R4660X SP1T2
Low Set Point
Bourdon Tube Rating
100 psig (6.9 bar) R4660X SP1J2
250 psig (17.2 bar) R4660X SP1K2
500 psig (34.5 bar) R4660X SP1L2
1000 psig (69.0 bar) R4660X SP1M2
1500 psig (103.4 bar) R4660X SP1N2
2500 psig (172.4 bar) R4660X SP1P2
5000 psig (344.8 bar) R4660X SP1R2
7500 psig (517.1 bar) R4660X SP1S2
10,000 psig (689.5 bar) R4660X SP1U2
Supply Test Plunger Assembly
––– Supply Test Plunger Assembly R4660X STP22
Tamper-Resistant Cover
––– Tamper-Resistant Cover (Includes hex
tool and key 6) R4660X TPC12
Parts List
1 Base, hard coat anodized aluminum
w/duplex seal 58A1045 X022
2 Case, polyester 29A5201 X012
3 Case cover, polyester 48A1060 X012
4 Cover, polyester 38A1057 X012
5 Case Cover Screw, stainless steel/polyester 18A1080 X012
6 Cover Screw, stainless steel/polyester (2 req’d) 18A1082 X012
7 Process Block, 316 stainless steel
1/4-inch Female Process Connection 26A6962 X012
8 Process Tubing,
stainless steel
For all Bourdon Tube ranges
up to 2500 psig (170 bar) 18A1089 X012
For Bourdon tube ranges
5000 psig (350 bar) or over 18A1089 X022
N05500 (K-Monel) for NACE
For all Bourdon Tube ranges
up to 2500 psig (170 bar) 18A1089 X042
For Bourdon tube ranges
5000 psig (350 bar) or over 18A1089 X052
10 Flapper Spring Support, stainless steel 18A1050 X012
11 Blow-Out Plug, silicone 2V7660 05312
12 Cable Assembly, stainless steel/nylon 18A1078 X012
13 Cover Plate, stainless steel
w/o output indication 18A1053 X012
w/output indication 18A4356 X012
14* Cover Plate Gasket, neoprene 18A1052 X012
18 Flapper Spring, stainless steel
Bourdon Tube Ratings to 100 psig (7 bar) 18A6212 X012
For all other Bourdon tubes 18A9195 X012
19 Cable Screw, stainless steel 18A1070 X012
20 Vent Screen, stainless steel 0L0783 43062
Key Description Part Number
21 Machine Screw, stainless steel (4 req’d) 1J8415 X0012
22 Self-Tapping Screw, stainless steel (5 req’d) 16A6959 X022
23* O-Ring, nitrile (3 req’d) 1B8855 06992
24* O-Ring, nitrile (3 req’d) 18A1088 X012
25* O-Ring, nitrile 1D2375 X0022
26 Cap Screw, stainless steel (2 req’d)
1/4-inch NPT Female Process Connection 18A1087 X022
27 Machine Screw, stainless steel (2 req’d) 1H3403 X0012
28 Machine Screw,stainless steel (3 req’d) 1A5733 X0012
54 Cleanout Assembly 19A6031 X012
57 Machine Screw, stainless steel (2 req’d) 1B2752 X0022
67 Knob (w/o set point indication)
(1)
18A3589 X012
68 Screw, stainless steel
(2)
1P4373 X0012
69 Locking Disk, Noryl
(w/o set point indication)
(1)
28A3590 X012
70 Locking Nut, aluminum/PTFE anodized
(w/o set point indication)
(1)
18A3591 X012
71 Locking Wedge, Noryl
(w/o set point indication)
(2)
18A3592 X012
73 Range Label See table
74 Front Plate, stainless steel
w/o Output Indication
Low Set 29A3434 X012
High Set 29A3433 X012
High/Low Set 29A3435 X012
w/ Output Indication
Low Set 29A3440 X012
High Set 29A3439 X012
High/Low Set 29A3441 X012
75 Mounting Plate, stainless steel (not shown)
Panel Mounting 28A1073 X012
Actuator Yoke Mounting 28A6338 X012
Actuator Casing Mounting 28A6336 X012
Pipestand Mounting 37A0724 X012
76 Nameplate, stainless steel - - -
77 Self-Tapping Screw, stainless steel (4 req’d) 19A5229 X012
81 Sealant, ZINK PLATE No. 770
(not furnished with pilot)
84 Cap Screw, pl steel (not shown)
Actuator Yoke Mounting (5 req’d) 1A3816 24052
Actuator Casing Mounting (3 req’d) 1C6312 24052
Pipestand Mounting (3 req’d) 1A3816 24052
85 Lock Washer, pl steel (not shown)
Actuator Yoke Mounting (5 req’d) 1C2257 28982
Actuator Casing & Pipestand Mounting (3 req’d) 1C2257 28982
86 Pipe Clamp, pl steel (not shown)
Pipestand Mounting (2 req’d) 1P4270 28982
87 Sealant, LOCTITE No. 222
(not furnished with pilot)
88 Output Indicator 19A0332 X012
89 Elbow Fitting, stainless steel
(output indicator) (2 req’d) 19A0333 X012
90 Tubing, Nylon (output indicator) 19A0331 X022
91 Tubing, polyethylene (output indicator (2 req’d) 19A0351 X022
92* Gasket, Nitrile (for panel mounting) 28A4549 X012
––– Hex Tool, alloy steel (not shown)
Tamper-Resistant Cover 10B3580 X012
*Recommended spare parts
1. One required for high or low set point versions; two required for high/low versions.
2. Two required for high or low set point versions; four required for high/low versions.
To Next Page
Loading...
