Fleck 5600 User Manual (English)

Other manuals for Fleck 5600

Service Manual28 pages

Installation Instructions19 pages

Questions and Answers:

D
David TaylorAug 16, 2025
How to fix excessive water in brine tank of Fleck 5600 Water Dispenser?
- C
  Cindy JohnsonAug 16, 2025
  If there's excessive water in the brine tank of your Fleck Water Dispenser, consider these possible causes and solutions: * The by-pass valve might be open. Ensure the by-pass valve is closed. * There might be no salt in the brine tank. Add salt to the brine tank, maintaining the salt level above the water level. * The injectors or screen could be plugged. Replace the injectors and screen. * There might be insufficient water flowing into the brine tank. Check the brine tank fill time and clean the brine line flow control if it's plugged.
J
jacobwilliamsAug 19, 2025
What to do if Fleck 5600 fails to draw brine?
- T
  Timothy KelleyAug 19, 2025
  If your Fleck Water Dispenser fails to draw brine, consider the following potential causes and solutions: * The drain line flow control is plugged. Clean the drain line flow control. * The injector is plugged. Clean or replace the injectors. * The injector screen is plugged. Replace the screen. * The line pressure is too low. Increase the line pressure, ensuring it's at least 20 PSI at all times. * There's an internal control leak. Change the seals and spacers and/or piston assembly.
J
John VillaAug 22, 2025
Why Fleck Water Dispenser fails to regenerate?
- M
  Michael MedinaAug 22, 2025
  If your Fleck Water Dispenser fails to regenerate, it could be due to several reasons: * Interrupted electrical service to the unit. Ensure permanent electrical service by checking the fuse, plug, pull chain, or switch. * A defective timer. Replace the timer. * A power failure. Reset the time of day.
T
Tracy ColeAug 25, 2025
Why Fleck 5600 control cycles continuously?
- J
  Jerome SheltonAug 26, 2025
  If the control of your Fleck Water Dispenser cycles continuously, it's likely due to a faulty timer mechanism. Replacing the timer should resolve this issue.
J
Justin WilkinsonAug 28, 2025
Why is my Fleck 5600 delivering hard water?
- C
  Curtis EsparzaAug 28, 2025
  If your Fleck Water Dispenser is delivering hard water, it's possible that the reserve capacity has been exceeded. To resolve this, check the salt dosage requirements and reset the program wheel to provide additional reserve.
J
Juan PriceAug 31, 2025
What to do if I have loss of water pressure with Fleck 5600 Water Dispenser?
- A
  Adam Shah MDAug 31, 2025
  If you're experiencing a loss of water pressure with your Fleck Water Dispenser, there are a couple of potential causes: * The drain line flow control might be plugged, in which case you should clean it. * The line pressure might be too low. Ensure that the line pressure is at least 20 PSI at all times and increase it if necessary.
A
Amanda AllenSep 3, 2025
Why does my Fleck Water Dispenser use too much salt?
- S
  seanowensSep 3, 2025
  If your Fleck Water Dispenser is using too much salt, it could be due to: * An improper salt setting. Check the salt usage and salt setting to ensure they are correct. * Excess water in the brine tank. Refer to problem No. 7 for solutions related to excessive water in the brine tank.
R
Robert GrahamSep 6, 2025
Why is there iron in the conditioned water from my Fleck Water Dispenser?
- J
  john99Sep 6, 2025
  If you're finding iron in the conditioned water from your Fleck Water Dispenser, here are potential causes: * Iron buildup in the line to the water conditioner. Clean the line. * Iron buildup in the water conditioner itself. Clean the control and add resin cleaner to the resin bed, also increase the frequency of regeneration. * The inlet of the control is plugged due to foreign material. Remove the piston and clean the control.
V
victor05Sep 9, 2025
Why is there salt water in the service line of my Fleck 5600?
- J
  John BarberSep 9, 2025
  If you're experiencing salt water in the service line of your Fleck Water Dispenser, it could be due to: * A plugged injector system. Clean the injector and replace the screen. * The timer not cycling. Replace the timer. * Foreign material in the brine valve. Clean or replace the brine valve. * Foreign material in the brine line flow control. Clean the brine line flow control.
K
Kenneth FloresSep 12, 2025
Why does my Fleck 5600 drain flows continuously?
- T
  tiffanydavisSep 12, 2025
  If your Fleck Water Dispenser's drain flows continuously, it may be due to: * Foreign material in the control. Remove the piston assembly and inspect the bore, remove any foreign material, and check the control in various regeneration positions. * An internal control leak. Replace the seals and/or piston assembly. * The control valve is jammed in the brine or backwash position. Replace the seals and/or piston assembly. * The timer motor has stopped or jammed. Replace the timer.