EasyManua.ls Logo

Flotec FP0F360AC - User Manual

Flotec FP0F360AC
36 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Installation/Operation/Parts
For further operating,
installation, or maintenance
assistance:
Call 1-800-365-6832
English .................... Pages 2-12
Installation/Fonctionnement/Pièces
Pour plus de renseignements
concernant l’utilisation,
l’installation ou l’entretien,
Composer le
1 (800) 365-6832
Français ............... Pages 13-24
Instalación/Operación/Piezas
Para mayor información sobre
el funcionamiento, instalación o
mantenimiento de la bomba:
Llame al 1-800-365-6832
Español ...............Paginas 25-36
FP874 (10/29/09)
®
OWNER’S MANUAL
4" Submersible Pumps
Two and Three Wire, 1/2 thru 1
1
2 HP, 60 Hz
U.S. Patent 5,133,639
NOTICE D’UTILISATION
Pompe submersible de 4 po
à deux et trois fils, de 1/2 à 1
1
2 ch, 60 Hz
de brevet U.S. 5,133,639
MANUAL DEL USUARIO
Bombas sumergibles de 4"
de dos y tres hilos, 1/2 a 1
1
2 CV, 60 Hz
Patente de EE.UU. No. 5,133,639
®
P.O. Box 342, Delavan, WI 53115
Phone:
1-800-365-6832
Fax:
1-800-526-3757
E-Mail:
info@flotecwater.com
Web Site:
http://www.flotecwater.com

Questions and Answers

  • P
    Paul CaseyJul 27, 2025
    What to do if my Flotec Water Pump motor fails?
    • P
      Pamela BradyJul 27, 2025
      If the motor fails, the suggested solution is to replace the entire pump.
  • I
    Isaac BrownAug 5, 2025
    What to do if Flotec FP0F360AC discharge from faucets is air or milky?
    • A
      Andrew DunnAug 5, 2025
      If the water discharging from your faucets appears milky or contains air when using a Flotec Water Pump, it could be due to gas present in the well water. To address this, remove the bleeder orifices and plug the tees, ensuring that these plugs are completely sealed to prevent leaks. Another potential cause is a malfunctioning air volume control. If this is the case, replace the control as needed.
  • G
    Gregory GloverNov 15, 2025
    Why is my Flotec Water Pump delivering little or no water?
    • L
      Louis MontgomeryNov 16, 2025
      If your Flotec Water Pump isn't delivering enough water, several factors could be at play. First, the bleeder orifice check valve might be stuck or incorrectly installed; try freeing it or reversing its installation. Low water levels can also be a culprit, so lower the pump further into the well, ensuring it remains at least 5 feet above the well's bottom. Insufficient voltage can hinder performance; consider installing larger wires from the meter to the control box and from the control box to the pump, or consult your power company about raising the supply voltage. Additionally, a plugged intake screen can restrict water flow, requiring cleaning or replacement. A stuck check valve at the pump discharge could also be the issue; try freeing the check valve. Lastly, worn impellers and diffus...

Summary

Safety Instructions

Hazardous Condition Warnings

Covers warnings for hazardous pressure, voltage, freezing, and general installation safety.

Pre-Installation and Grounding

Essential Grounding Procedures

Outlines critical steps for grounding the pump, motor, and control box for safety.

Control Box and Wiring Diagrams

Control Box Mounting and Selection

How to mount control boxes correctly and match them to motor specifications.

Detailed Installation Procedures

Electrical Grounding and Bonding

Critical safety instructions for grounding and bonding the pump and motor assembly.

Troubleshooting Common Issues

Motor Start and Fuse Problems

Solutions for motor failures, blown fuses, and overload protector trips.

Flotec FP0F360AC Specifications

General IconGeneral
BrandFlotec
ModelFP0F360AC
CategoryWater Pump
LanguageEnglish

Related product manuals