EasyManua.ls Logo

Flotec FP0S2450A-08 - User Manual

Flotec FP0S2450A-08
20 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
®
P.O. Box 342, Delavan, WI 53115
Phone:
1-800-365-6832
Fax:
1-800-526-3757
E-Mail:
info@flotecwater.com
Web Site:
http://www.flotecwater.com
OWNER’S MANUAL
Submersible Sump Pumps
NOTICE D’UTILISATION
Pompes submersibles
pour puisard
MANUAL DEL USUARIO
Bombas sumergibles
para sumideros y efluentes
Installation/Operation/Parts
For further operating,
installation, or maintenance
assistance:
Call 1-800-365-6832
English ...................... Pages 2-7
Installation/Fonctionnement/Pièces
Pour plus de renseignements
concernant l’utilisation,
l’installation ou l’entretien,
Composer le
1 (800) 365-6832
Français ................. Pages 8-12
Instalación/Operación/Piezas
Para mayor información sobre
el funcionamiento, instalación o
mantenimiento de la bomba:
Llame al 1-800-365-6832
Español ...............Paginas 13-19
FP526 (Rev. 2/15/07)
1569 0195
1572 0195

Table of Contents

Questions and Answers

  • K
    Kara CowanAug 2, 2025
    How to troubleshoot Flotec FP0S2450A-08 that won't start?
    • C
      Crystal HarringtonAug 2, 2025
      If your Flotec Water Pump won’t start or run, start by checking if it's properly plugged into a working outlet. If the pump is plugged in, inspect the fuse and replace it with one of the correct size if it's blown. Also, low line voltage can be a factor; check the wiring size from the main switch if the voltage is below the recommended minimum. If the wiring is OK, contact your power company or hydro authority. If these steps don't resolve the issue, the motor or float switch might be defective, requiring you to replace the pump or the float switch, respectively. Lastly, if the impeller won’t turn, remove the lower pump body and locate and remove any obstructions.
  • T
    Taylor WilliamsAug 17, 2025
    Why does my Flotec Water Pump start and stop frequently?
    • N
      nicolepriceAug 18, 2025
      If your Flotec Water Pump starts and stops too often, it might be due to backflow from the piping. To resolve this, install or replace the check-valve. Another cause could be a faulty float switch, which would require replacement.
  • K
    Karen JeffersonAug 26, 2025
    What causes a Flotec Water Pump to run continuously?
    • C
      Cynthia RobinsonAug 26, 2025
      If your Flotec Water Pump won’t shut off, the problem could be a defective float switch, which needs to be replaced. Another potential cause is a restricted discharge due to an obstacle or ice in the piping; in this case, remove the pump and clean both the pump and the piping. Also, the float itself might be obstructed, so remove any obstructions that you find. Lastly, a restricted intake screen could be the culprit; remove the pump and clean both the intake screen and the impeller.
  • K
    Kelly OdomNov 8, 2025
    What to do if my Flotec FP0S2450A-08 Water Pump delivers little or no water?
    • J
      Jennifer JonesNov 8, 2025
      If your Flotec Water Pump operates but delivers little or no water, the issue could stem from several causes. First, verify that the line voltage isn't too low by checking the wiring size from the main switch. If the voltage is under the recommended minimum, this could be the cause. Also, the impeller might be obstructed; remove the pump and clean out the impeller. Alternatively, the impeller might be plugged or the parts are worn or defective, try cleaning the impeller, but if that doesn't work, replace the pump. Ensure that the check valve is correctly installed and if a check valve is installed without a vent hole, drill a hole with a diameter of 1/16" - 1/8" (1.6mm - 3.2mm) between the pump discharge and check valve, positioning it 1-2” above where the discharge pipe screws into the pu...

Summary

Submersible Sump Pump Owners Manual

Installation, Operation, and Parts

Guidance for operating, installing, and obtaining parts for the sump pump.

Specifications and Safety Information

Product Description

Overview of the submersible sump pump's design and intended use.

Technical Specifications

Details on power requirements, liquid temperature, and discharge sizes.

Performance Data

Flow rate (GPH/LPH) at various feet of lift for different pump models.

Electrical and Switch Specifications

Details on motor amperage, circuit requirements, and switch settings.

General Safety Information

Essential safety guidelines for operating and maintaining sump pumps.

Installation and Operation Procedures

Float Switch Installation

Instructions for installing float switches on sump pump models.

Pump Installation Steps

Detailed steps for installing the sump pump, including plumbing and electrical connections.

Installation Safety Precautions

Critical safety warnings during pump installation and operation.

Pump Operation Guide

Operational Guidelines and Warnings

Key operating principles, motor protection, and safety warnings.

Vertical Switch Assembly Instructions

Step-by-step guide for assembling the vertical float switch.

Tethered Float Switch Operation

Information on the tethered float switch and its preset length.

Repair Parts and Diagrams

Parts Identification and Compatibility

Lists and diagrams for identifying replacement parts for plastic and cast iron series pumps.

Troubleshooting Guide

Common Pump Issues and Solutions

Addresses common pump symptoms, their causes, and recommended corrective actions.

Warranty Information

Warranty Exceptions and Periods

Details specific warranty periods for different pump models and exceptions.

General Warranty Terms and Conditions

Outlines the general terms, conditions, and limitations of the manufacturer's warranty.

Flotec FP0S2450A-08 Specifications

General IconGeneral
ModelFP0S2450A-08
CategoryWater Pump
TypeSubmersible Utility Pump
Voltage115V
Maximum Head25 ft
Discharge Size1-1/4 in
Construction MaterialThermoplastic
Cord Length10 ft
Horsepower0.25 HP

Related product manuals