Fluke ScopeMeter 190-062 - Chapter 1: Using the Scope and Meter

142 pages

To Next Page

To Previous Page

Fluke-062, -102, -104, -202, -204, -502, -504

Service Manual

viii

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Main Page

Table of Contents4
Safety Instructions12
Introduction14
Safety Precautions14
Caution and Warning Statements14
Symbols15
Li-Ion Battery Pack18
Safe Storage of Battery Pack18
Safe Use of Battery Pack19
Safe Transport of Battery Pack20
Safe Disposal of Battery Pack20
Specifications22
Introduction24
Oscilloscope24
Automatic Scope Measurements27
Meter Measurements for Fluke 190-Xx430
Meter Measurements for Fluke 190-Xx230
Recorder32
Zoom, Replay and Cursors33
Miscellaneous33
Environmental35
Certifications35
Safety35
10:1 Probe VPS41037
Electromagnetic Immunity37
Parts List38
Introduction40
How to Obtain Parts40
Final Assembly Parts41
Accessory List45
Performance Verification46
Introduction48
Equipment Requirements for Verification49
General Instructions49
Operation Instructions49
Reset the Test Tool49
Menu Navigation50
Standard Test Tool Setup50
Display and Backlight Test52
Scope Input A, B, C, D Tests53
Input A, B, C, D Vertical Accuracy Test53
Input A, B, C, D DC Voltage Accuracy Test56
Input A, B, C, D AC Voltage Accuracy Test (LF)59
Input A, B, C, D AC-Coupled Lower Frequency Test61
Input A, B, C, D Peak Measurements Test62
Input A, B, C, D Frequency Measurement Accuracy Test63
Input A&B / C&D Phase Measurements Test64
Time Base Test65
Input a Trigger Sensitivity Test66
Input a AC Voltage Accuracy (HF) and Bandwidth Test68
Input B Trigger Sensitivity Test69
Input B AC Voltage Accuracy (HF) and Bandwidth Test70
Input C Trigger Sensitivity Test71
Input C AC Voltage Accuracy (HF) and Bandwidth Test72
Input D Trigger Sensitivity Test73
Input D AC Voltage Accuracy (HF) and Bandwidth Test75
Video Test with SC600 Scope Calibration Option76
External Trigger Level Test79
Meter Tests80
Meter DC Voltage Accuracy Test80
Meter (DMM) Tests80
Meter AC Voltage Accuracy and Frequency Response Test81
Continuity Function Test82
Diode Test Function Test82
Ohms Measurements Test83
Probe Calibration Generator Test84
Calibration Adjustment86
Introduction88
General89
Calibration Number and Date89
General Instructions89
Equipment Required for Calibration90
Calibration Procedure Steps90
How to Start the Calibration91
Contrast Calibration Adjustment92
Warming-Up and Pre-Calibration94
Final Calibration for V11.10 and Later95
Warming-Up 2, Warm-Up Final, and ADC Timing96
Input a LF-HF Gain97
Input B LF-HF Gain99
Input C LF-HF Gain101
Input D LF-HF Gain103
Input AB Position105
Input AB LF-HF Gain and Position105
Input Pos ABCD (AB) Calibration107
Input ABCD (AB) Noise F FBW Calibration107
Input AB Volt Gain107
Multimeter Meter Zero109
Multimeter Volt Gain109
Multimeter Ohm Gain111
Final Calibration (Firmware: V10.9 and Lower)113
Error Messages113
Warm-Up Final and ADC Timing113
Input a LF-HF Gain114
Input B LF-HF Gain116
Input C LF-HF Gain118
Input D LF-HF Gain120
Input ABCD (AB) LF-HF Gain121
Input ABCD (AB) Position123
Input ABCD (AB) Volt Gain123
Input ABCD (AB) Zero124
Multimeter Volt Gain125
Multimeter Numeric Zero126
Multimeter Ohm Gain126
Save Calibration Data and Exit128
Probe Calibration129
Disassembly132
Introduction134
Disassembly and Reassembly Procedures134
Required Tools134
Remove the Tilt Stand, Hang Strap, and Side Strap134
Open the Test Tool, Remove the Battery Pack135
How to Access the Top Side of PCA136
How to Access the Bottom Side of PCA136
Access to LCD, Keypad Foil, and Keypad137
Disassembly Steps137

Fluke ScopeMeter 190-062 - Chapter 1: Using the Scope and Meter

Table of Contents

Other manuals for Fluke ScopeMeter 190-062

Related product manuals