Forest Diamond User Manual

07/2016 WDOC Diamond remote www.forestgroup.nl v1.4
FOREST DIAMOND REMOTE – 520109X460
TECHNICAL SPECIFICATION:
● 3V battery type CR2450 ● transmit range indoor max. 30mtr
● battery life < 3 years ● working temperature -10°C - +50°C
● frequency 433.92MHz ● each channel can control up to 20 receivers
● transmit power max. 10mW
channel leds
1 2 3 4 5 6
OPEN/UP switch on/off (keep
button pressed 3 seconds)
STOP
button P button (for program-
ming tubular motor)
CLOSE/DOWN
button
INSERT BATTERY:
channel up/down 1. remove screw
2. slide back cover upwards
to open remote and slide
in battery, +side up
BATTERY EMPTY:
After changing the battery, programmed receivers will stay in memory of wall
switch. Please follow the local regulations for disposal of the empty battery.
FOREST SHUTTLE S / L / M RECEIVER PROGRAMMING
You can recognize these Shuttle motors by the white antenna cable
To program a Diamond Remote to a Shuttle S / L / M Receiver:
antenna
LED MOVES FROM LED STARTS BLINKING
1
st
→2
nd
→3
rd
LED
3x 1x for 5 sec.
press 1x OPEN button
Same procedure, but press CLOSE instead of OPEN, will erase the programmed channel.
Do not mount the motor within 1 meter from other equipment and receivers.
This will interfere with the receiver.

Forest Diamond Specifications

General

Brand	Forest
Model	Diamond
Category	Remote Control
Language	English

Summary

Forest Diamond Remote Operation

Technical Specifications

Details on battery type, life, frequency, transmit power, range, and temperature.

Remote Control Layout and Battery

Diagrams and instructions for button functions, battery insertion, and empty battery notes.

Forest Shuttle S/L/M Receiver Programming

Diamond Remote to Shuttle Receiver Pairing

Procedure to program a Diamond Remote to a Shuttle S/L/M Receiver using specific button presses.

Forest Multi Receiver Click On Setup

Technical Specifications

Details on power source, connection, operating temperature, and controlled devices.

Wall Switch to Receiver Programming

Steps to program a wall switch to a click-on receiver, including button presses and LED feedback.

Receiver Channel Management

Procedures for removing a programmed channel and deleting all programmed channels.

Forest Multi Receiver and FMS/BCS Receiver Setup

Shuttle M Receiver Technical Details

Specifications for Shuttle M receiver, including power, cable options, and temperature.

FMS/BCS Receiver Technical Details

Specifications for FMS/BCS receiver, including power, motor control, and temperature.

Receiver Programming and Channel Control

Instructions for programming remotes, removing channels, and deleting all channels for multi receivers.

Tubular Motor Remote Control and Limits

Programming Remote to Tubular Motor

Steps for pairing a remote, adding multiple remotes, and cancelling all remotes for tubular motors.

Changing Tubular Motor Rotation Direction

Procedure to reverse the rotation direction of a tubular motor by pressing the motor button.

Adjusting Tubular Motor End Limits

Setting Upper and Lower Motor Limits

Instructions for setting the upper and lower travel limits for tubular motors.

Tubular Motor Limit Cancellation and Reverse Setting

Cancelling Tubular Motor End Limits

Procedure to cancel previously set upper and lower travel limits for tubular motors.

Tubular Motor Reverse Direction Setting

Method to reverse the direction of rotation for a tubular motor when it's not running.

BS 24V Double Shaft Motor Setup

Technical Specifications

Details on power, torque, speed, running time, weight capacity, and compatibility.

Wall Switch to BS Motor Programming

Steps for programming a wall switch to a BS motor, including channel selection and button presses.

BS Motor Direction Change

Procedure to change the motor direction using the wall switch, involving specific button presses.

Setting BS 24V Double Shaft Motor Limits

Setting Upper End Limit

Instructions to set the desired upper travel limit for the BS 24V double shaft motor.

Setting Lower End Limit

Instructions to set the desired lower travel limit for the BS 24V double shaft motor.

Deleting BS Motor Limits and Memory

Procedures for deleting specific limits and clearing all programmed memory for BS motors.