What to do if Fresenius Medical Care 2008K Medical Equipment displays A.13 (Arterial or SN Blood Pump Message)?
If the pump is turning in the wrong direction, press the RESET key to clear the message. Verify that the pump rotor is turning in a clockwise direction. If not, take the blood pump out of service and alert a qualified technician.
What to do if Fresenius Medical Care 2008K Medical Equipment displays A.11 (Arterial or SN Blood Pump Message)?
If the pump is not reaching speed at maximum voltage, press the RESET key to clear the message. If the problem persists, take the blood pump module out of service and alert a qualified technician.
What to do if Fresenius Medical Care Medical Equipment shows Blood Leak?
If the blood leak detector has detected blood or air in the dialysate: 1. Press RESET to reset the alarm. If allowed, press Override to continue dialysis if the machine cannot be reset. 2. Check dialysate fluid for blood with Hemastix. If the Hemastix test is negative, recheck with a new Hemastix. If negative after three checks: * Press Override to run the blood pump for up to 3 minutes while troubleshooting the alarm. * Check the dialysate lines for air leaks, especially at the connectors and the filter. * Press RESET to reset the alarm. If unable to reset the alarm and the Hemastix test is positive, return the patient’s blood and alert a qualified technician.
What to do if Fresenius Medical Care 2008K Medical Equipment displays *** 24 V HIGH?
If the device shows '*** 24 V HIGH' due to the electronic self-test and power supply limits exceeded, turn the machine power off and back on. If the alarm is not cleared, take the machine out of service and alert a qualified technician.
What to do if Fresenius Medical Care 2008K displays 12V POWER FAIL?
If the device shows '12V POWER FAIL' due to the electronic self-test and power supply limits exceeded, turn the machine power off and back on. If the alarm is not cleared, take the machine out of service and alert a qualified technician.
What to do if Fresenius Medical Care 2008K Medical Equipment displays *** 5V LOW ***?
If the device shows '*** 5V LOW ***' due to the electronic self-test and power supply limits exceeded, turn the machine power off and back on. If the alarm is not cleared, take the machine out of service and alert a qualified technician.
What to do if Fresenius Medical Care 2008K displays *** 5V HIGH ***?
If the device shows '*** 5V HIGH ***' due to the electronic self-test and power supply limits exceeded, turn the machine power off and back on. If the alarm is not cleared, take the machine out of service and alert a qualified technician.
What to do if Fresenius Medical Care 2008K displays Act Blood Pump Failed?
If the device shows 'Act Blood Pump Failed' due to an electronic self-test failure, turn the machine power off and back on. If the alarm is not cleared, take the machine out of service and alert a qualified technician.
What to do if Fresenius Medical Care 2008K Medical Equipment displays ACID PUMP ALARM?
This is a pump failure warning. A single occurrence is not a problem if the machine automatically resets. If the problem persists for longer than one minute or occurs repeatedly, turn power off and back on. If the warning is not cleared, take the machine out of service.
What to do if Fresenius Medical Care 2008K Medical Equipment displays Blood Pump Stopped?
If the blood pump is on and the speed is set, but the blood pump has stopped for a period exceeding its set time limit: 1. Inspect the blood pump module to see if: * The blood pump door is closed. * The pump tube segment is properly positioned. Correct if necessary. 2. Press the RESET key to reset the alarm. 3. If a single needle pump is in the machine, the Single Needle option in the “Tests & Options” screen must be off and single-needle pump speed set to zero. 4. Set blood flow rate to zero and slowly increase flow to the prescribed rate. If unable to resume blood flow rate, replace the blood pump module. If a blood pump module is not available, hand crank blood to the patient and alert a qualified technician.
General| Manufacturer | Fresenius Medical Care |
|---|---|
| Model | 2008K |
| Type | Hemodialysis Machine |
| Dialysate Flow Rate | 300-800 mL/min |
| Arterial Pressure Monitoring | Yes |
| Venous Pressure Monitoring | Yes |
| Power Supply | 50/60 Hz |
| Ultrafiltration Rate | 0-4000 mL/h |
| Display | LCD |
| Safety Features | Blood leak detection, air detection, pressure monitoring, temperature monitoring, conductivity monitoring |
| Conductivity Range | 13.0-16.0 mS/cm |
To Next Page
