Fresenius Medical Care 2008K User Manual (English)

Other manuals for Fresenius Medical Care 2008K

Operator's Manual240 pages

Maintenance72 pages

Calibration Manual84 pages

Technical Manual216 pages

Questions and Answers:

S
Sandy AllenAug 27, 2025
What to do if Fresenius Medical Care 2008K displays Venous Pressure Alarm (with the lower Venous Pressure Alarm limit flashing)?
- O
  Olivia WhiteAug 27, 2025
  If low pressure is detected in the venous drip chamber: 1. Check venous tubing for kinked line, clotting or clamps. 2. Check for a disconnected line. 3. Ensure that the transducer protector is dry and the monitor line is open. Replace the transducer protector, if necessary. 4. Press RESET to reset alarm. Press the RESET key again and hold for one second to select new alarm limits. If you are unable to reset the alarm, take the machine out of service and alert a qualified technician.
C
Charles NielsenAug 26, 2025
What to do if Fresenius Medical Care 2008K displays Low Temperature?
- M
  millerphilipAug 27, 2025
  If the actual dialysate temperature has exceeded the low-temperature alarm limit and the machine is in bypass mode: 1. Check that the machine is in Dialysis status and the dialysate flow is on. 2. Check that the heater switch on the back panel is in the on (?) position. 3. Check the water supply to the machine for excessively cold temperature and correct. 4. Check the Temperature value in the “Home” screen. Re-enter it if necessary and allow five minutes for the temperature to stabilize. 5. If unable to attain the prescribed temperature, discontinue treatment and alert a qualified technician.
S
Stephen YorkAug 25, 2025
What to do if Fresenius Medical Care Medical Equipment displays High Temperature?
- H
  Henry HowardAug 26, 2025
  If the actual dialysate temperature has exceeded the high-temperature alarm limit and the machine is in bypass mode: 1. Ensure that water is flowing to the machine when turned on. 2. Check the water supply to the machine for excess temperature and correct if necessary. 3. If heat disinfection was recently performed, place the machine in rinse cycle to decrease temperature. 4. Check the Temperature value in the “Home” screen. Re-enter it if necessary and allow five minutes for the temperature to stabilize. 5. Check that the dialysate flow at drain line is 500 ml/min ± 50 ml.
T
Thomas HendricksAug 25, 2025
What to do if Fresenius Medical Care 2008K Medical Equipment shows Venous Pressure Alarm (with the upper Venous Pressure Alarm limit flashing)?
- K
  Katie MartinezAug 25, 2025
  If high pressure is detected in the venous drip chamber: 1. Check venous tubing for loose connections, kinks, clotting, or loose clamps. 2. Ensure that the transducer protector is dry and the monitor line is open. Replace the transducer protector, if necessary. 3. Check access point for clotting and needle position. 4. Press RESET to reset alarm. Press the RESET key again and hold for one second to select new alarm limits. If the condition persists, reduce the blood flow rate. If the alarm won’t reset, take the machine out of service and alert a qualified technician.

Fresenius Medical Care 2008K Specifications

General

Manufacturer	Fresenius Medical Care
Model	2008K
Type	Hemodialysis Machine
Dialysate Flow Rate	300-800 mL/min
Arterial Pressure Monitoring	Yes
Venous Pressure Monitoring	Yes
Power Supply	50/60 Hz
Ultrafiltration Rate	0-4000 mL/h
Display	LCD
Safety Features	Blood leak detection, air detection, pressure monitoring, temperature monitoring, conductivity monitoring
Conductivity Range	13.0-16.0 mS/cm