FRIEDLAND SA3 PLUS - User Manual

Questions and Answers

C
Caleb RodriguezAug 20, 2025
How to troubleshoot FRIEDLAND SA3 PLUS control unit when the power LED is off?
- L
  Lisa GibsonAug 20, 2025
  If the control unit's power LED is off, there are several things to check: * First, ensure that other electrical circuits are working, as there may be a mains power failure. * Verify the mains adaptor is properly plugged into the socket and the socket is switched on. * Make sure the DC jack plug from the mains adaptor is securely connected to the control panel. * Inspect the fuse or MCB in the consumer unit that serves the control panel's circuit.
D
David MillerAug 22, 2025
Why is my FRIEDLAND Security System siren not responding to the control panel?
- J
  Johnny HaysAug 22, 2025
  If your siren isn't responding to the control panel, consider the following: * Make sure the 'House Code' is correctly set. * Check that the main siren configuration switch is set to SIREN. * Ensure the correct user access code is being entered at the control panel. * Verify the siren is within effective radio range of the control panel and not mounted near metal objects. * If the siren has a rechargeable battery, try cleaning the solar panel or replacing the battery if it's old. * You can also try fitting a new initial power-up battery and re-powering the siren.
L
Lauren WiseAug 25, 2025
What to do if my FRIEDLAND SA3 PLUS control unit is not accepting the user access code?
- F
  Frank DavenportAug 25, 2025
  If the control unit isn't accepting the user access code, consider these points: * Avoid pausing for more than 5 seconds between pressing keys. * If an incorrect code was entered, wait 5 seconds before re-entering the correct code. * If problems persist, try resetting the system to factory defaults and reprogramming it.
L
Lisa BarberAug 26, 2025
Why is my FRIEDLAND Security System control unit not responding to the detectors?
- S
  Shelia ValenciaAug 26, 2025
  If the control unit isn't responding to the detectors, check the following: * Make sure that the 'House Code' is correctly set. * Ensure the detector is within the effective radio range of the control panel and is not mounted close to metal objects. * If the detector battery is low, replace it.
L
leetimothyAug 27, 2025
What causes a full alarm on my FRIEDLAND SA3 PLUS Security System when not triggered by an intruder?
- K
  Karen WatersAug 28, 2025
  A full alarm condition when the system hasn't been triggered by an intruder could be due to: * Tamper switch activation: Check all detector battery covers to ensure they are correctly fitted. * Tamper switch activation: Check the control panel and siren are securely mounted to the wall and the tamper switch is closed. * It could also be due to the Personal Attack Alarm being activated from a Remote Control or Control Panel or the Jamming detection circuit being operated.
T
tbryantAug 29, 2025
Why is my FRIEDLAND SA3 PLUS Security System PIR movement detector not detecting movement?
- J
  jonathanrodriguezAug 30, 2025
  If the PIR movement detector isn't detecting movement, you can try the following: * Ensure battery connections are good. * If the pulse count is set too high, reset it to one pulse detection. * Make sure that the detector is mounted the correct way up, with the detection window at the bottom, and at the correct height (2-2.5m). * Ensure DIP switches 1-4 of SW3 are correctly set. * Allow up to three minutes for the detector to stabilize. * Ensure the detector is within effective radio range of the control panel and is not mounted close to metal objects which may interfere with RF transmission.
R
rwheelerAug 31, 2025
How to stop false alarms from my FRIEDLAND SA3 PLUS PIR movement detector?
- W
  warneramySep 1, 2025
  To prevent false alarms from a PIR movement detector, try the following: * Ensure the detector isn't pointing at a heat source or moving object. * Make sure the detector isn't mounted above a radiator or heater. * Ensure the detector isn't facing a window or in direct sunlight and is not in a draughty area. * If the pulse count is set too low, reset it to two pulse detection.
M
Margaret SmithSep 2, 2025
What to do if my FRIEDLAND Security System magnetic contact detector is not working?
- T
  Tiffany BerrySep 2, 2025
  If the magnetic contact detector isn't working, consider these steps: * Ensure batteries are connected with correct polarity and that battery connections are good. * Make sure the 'House Code' is correctly set. * Ensure DIP switches 9, 10, and 11 are set correctly. * Verify the detector is within the effective radio range of the control panel and not mounted close to metal objects. * If an additional magnetic contact detector is not connected, ensure the jumper link is fitted; if one is connected, ensure the jumper link is removed. * If an additional magnetic contact detector is connected, check that it is correctly wired and that the magnet is correctly positioned with the correct gap.
T
Troy RogersSep 4, 2025
Why are the siren and strobe operating on my FRIEDLAND SA3 PLUS Security System, but there's no alarm at the control panel?
- R
  Rebecca JordanSep 4, 2025
  If the siren and strobe are active but there's no alarm at the control panel, it could be due to the siren tamper switch being activated. Check the security of the siren's fixing to the wall and adjust the anti-tamper switch to ensure it is fully depressed. It could also be due to the siren jamming detection circuit being operated.
S
Steven Dawson DDSSep 6, 2025
What should I do if the 'Low Battery' LED is flashing on my FRIEDLAND Security System control unit?
- R
  rmilesSep 6, 2025
  If the 'Low Battery' LED is flashing on the control unit, check all PIR movement detectors for low battery indication (LED behind detection lens flashes when movement is detected) and renew batteries as required.