Fromm P355.0001.01 - User Manual

Questions and Answers

M
Michael BarrettAug 16, 2025
What to do if Fromm P355.0001.01 Packaging equipment doesn't cut the strap well?
- T
  Travis MccarthyAug 16, 2025
  If your Fromm Packaging equipment is not cutting the strap properly, it could be due to several reasons. The cutter might be worn or damaged, requiring a replacement. Another potential cause is a worn welding gripper, which should also be replaced. Additionally, inspect the coupler P32.1250 for incorrect adjustment and readjust if necessary. The welding time might be too short, so you can change the adjustment. Finally, a defective pressure spring N2.5237 could be the culprit, and replacing it might solve the issue.
R
Robin BlairAug 19, 2025
Why doesn't my Fromm Packaging equipment tension, even though the tensioning motor runs?
- D
  Darlene JonesAug 19, 2025
  If the tensioning motor runs but your Fromm Packaging equipment isn't tensioning, the tensioning wheel might be packed with strap residue or worn, causing it to mill on the strap. Try cleaning the tensioning wheel with compressed air or consider replacing it. Ensure the correct tensioning wheel is installed and assembled properly. Also, check the grippers for dirt, wear, or incorrect assembly; clean them, replace them, or reassemble them correctly. Defective gearing parts in the tensioning gear, such as a loose pinion P32.1123 on the tensioning motor, can also cause this issue. Inspect the tensioning gear and replace any defective parts.
E
Elizabeth ChangAug 22, 2025
What to do if the welding motor does not stop on Fromm Packaging equipment?
- J
  John WalkerAug 22, 2025
  If the welding motor on your Fromm Packaging equipment doesn't stop, it could be because the turn off valve or welding motor valve is jammed, or the welding time valve is blocked. Try checking and cleaning these parts, and replace any damaged components. Another possible cause is that the diameter of the air supply hose is too small. To resolve this, install an air supply hose with a minimum inner diameter of 9mm (3/8").
L
laurieprinceAug 26, 2025
What to do if the tensioning motor doesn’t run on Fromm P355.0001.01 Packaging equipment?
- J
  Jeffrey Lee Jr.Aug 26, 2025
  If the tensioning motor isn’t running on your Fromm Packaging equipment, it could be due to several reasons. The tensioning motor itself might be defective, or the tensioning gear could be damaged. Alternatively, the pneumatic control system might be malfunctioning. Another possible cause is that the needle free wheeling is assembled in reverse. In any of these cases, you should check the component parts and replace any damaged ones. If the needle free wheeling is assembled reversed, assemble it correctly.
M
Matthew BarrettAug 28, 2025
What to do if Fromm Packaging equipment doesn't weld, but the welding motor runs?
- G
  Greg ConleyAug 28, 2025
  If your Fromm Packaging equipment's welding motor runs, but it doesn't weld, the welding gripper or welding stop gripper might be dirty or worn. Clean and inspect these grippers, replacing any damaged ones. Also, a lose Pinion P32.1023 at the motor or welding eccentric, or a broken journal at the welding eccentric could be the problem. In such instances, check the component parts and replace any damaged ones.
K
Kevin RamseyAug 31, 2025
Why does the tensioning wheel turn back immediately after the tensioning cycle on Fromm Packaging equipment?
- B
  Brian PerezAug 31, 2025
  If the tensioning wheel turns back immediately after the tensioning cycle on your Fromm Packaging equipment, it's likely due to a defective needle free wheeling N3.4509. Check it and replace if necessary.
D
Daniel BarreraSep 3, 2025
What causes gear noise in Fromm Packaging equipment?
- P
  perrydavidSep 4, 2025
  Gear noise in Fromm Packaging equipment is often due to a worn tensioning or welding gear. To address this, check the component parts and replace any damaged ones.
J
Jessica LarsonSep 6, 2025
What to do if the welding motor doesn’t run on Fromm P355.0001.01 Packaging equipment?
- A
  Arthur HarrisonSep 7, 2025
  If the welding motor isn’t running on your Fromm Packaging equipment, it could be due to a defective welding motor or a malfunctioning welding mechanism. Another potential cause is a defective pneumatic control system. For each of these, check the component parts and replace any damaged ones.
K
Kevin RichardsonSep 9, 2025
How to fix welding time not adjustable on Fromm Packaging equipment?
- E
  Elizabeth PadillaSep 9, 2025
  If the welding time is not adjustable on your Fromm Packaging equipment, the welding time valve may be dirty or damaged. You should clean and check the component parts and replace any damaged ones.
A
Anne RiveraSep 12, 2025
How to fix tensioning force not adjustable on Fromm P355.0001.01?
- R
  Richard PriceSep 12, 2025
  If the tensioning force is not adjustable on your Fromm Packaging equipment, it is probably because the tension force control valve is dirty or damaged. Clean and check the component parts and replace any damaged ones.

Fromm P355.0001.01 Specifications

General

Model	P355.0001.01
Category	Packaging equipment
Manufacturer	Fromm
Sealing Type	Friction weld sealing
Strap Type	Polyester (PET) / Polypropylene (PP)
Strap Width	13 - 16 mm
Strap Thickness	0.4 - 1.05 mm