To Next PageTo Next PageHow to improve ignition during MMA welding with my Fronius Portable Generator?
If you're experiencing poor ignition properties during MMA welding, it could be that the incorrect welding process is selected. Ensure you select the appropriate welding process.
How to prevent the rod electrode from sticking on my Fronius Portable Generator?
If the rod electrode tends to stick, the value of the arc-force dynamic parameter (MMA welding) might be set too low. Increase the value of the arc-force dynamic parameter.
Why is the LED flashing for the set process on my Fronius Portable Generator?
The LED might be flashing because of single-phase operation with a welding current greater than 140A; select a welding current less than 140A and continue welding. Another reason could be a phase failure; check the mains lead.
What to do if the arc breaks during welding with my Fronius Portable Generator?
If the arc breaks during welding, it could be because the TIG Comfort Stop parameter value is set too low for the selected TIG welding process; adjust it to a higher value in the Setup menu. It could also be that the electrode (e.g. grooved electrode) voltage is too high; if possible, use an alternative electrode or a power source with more welding power. Finally, ensure that the correct welding process is selected: either "TIG welding" or "TIG pulsed arc welding".
Why am I having issues with TIG welding on my Fronius Portable Generator?
If you're experiencing problems with TIG welding, it could be due to several factors. The tungsten electrode polarity might be incorrect; connect the TIG welding torch to the negative pole. Another possibility is incorrect or missing shielding gas; use inert shielding gas (argon). Finally, ensure you've selected the correct welding process: TIG welding or TIG pulsed arc welding.
Why does the mains fuse keep tripping on my Fronius Portable Generator?
The mains fuse might be tripping because it's underrated or the circuit breaker is incorrect. Make sure to fuse the mains correctly, referring to the technical data. If the mains fuse trips in an open circuit, contact After-Sales Service.
What to do if my Fronius Portable Generator has no welding current?
If your Fronius Portable Generator isn't producing welding current, several factors could be at play. The duty cycle might be exceeded, causing the device to overload – in this case, stay within the duty cycle. The thermostatic automatic circuit breaker may have switched off the device; wait for the power source to come back on automatically after the cooling phase. Insufficient cooling air intake can also cause this, so ensure an adequate air supply. A dirty air filter could be the culprit; clean it. As a last resort, there may be a power module error, so turn the device off and on again.
How to fix severe spattering with my Fronius Portable Generator?
Severe spattering can occur due to several reasons. First, check if the electrode polarity is correct by referring to the manufacturer's instructions to reverse it if needed. Another cause might be a poor ground earth connection; make sure to fasten the earthing clamps directly to the workpiece. Lastly, the setup parameters might not be ideal for the selected welding process, so select the best setting in the Setup menu.
General| Brand | Fronius |
|---|---|
| Model | TransPocket 2500 |
| Category | Portable Generator |
| Language | English |
Explains safety notices, general principles, and operator duties.
Covers electrical hazards, protective devices, and personal safety measures.
Covers safe setup, transport, and normal operation practices.
Covers safe setup, cooling air, dust precautions, and electrical installation requirements.
Covers connection steps and selecting welding processes like HotStart and SoftStart.
Details how to set amperage and ignite the welding arc.
Covers torch, grounding, gas, and remote control connections for TIG welding.
Explains how VRD reduces voltage for safety and when it is active/inactive.
Emphasizes safety precautions before and during troubleshooting.
Provides common causes and solutions for welding issues like no current or poor ignition.
Details solutions for issues like no welding current, arc breaks, electrode sticking, and fuse trips.
Explains LED indicators for process selection, open circuit, and voltage issues.
