How to fix FuelTech Automobile Accessories FT450 unit that doesn’t turn on?
If your FuelTech Automobile Accessories FT450 unit doesn’t turn on, take these steps: 1. Check the battery voltage. 2. Check the power and ground cables. 3. Check the Switched 12V cable. 4. Check the ECU harness cables.
What to do if FuelTech Automobile Accessories FT450 reads RPM but engine doesn’t start?
If your FuelTech Automobile Accessories FT450 reads RPM but the engine doesn’t start: 1. Check if there is spark and injector pulse. 2. Check fuel pressure. 3. Check crank trigger alignment and TPS calibration. 4. Verify if outputs are activated and properly configured. 5. Check the O2 sensor reading.
Why FuelTech Automobile Accessories engine runs but doesn’t idle?
If the engine runs but doesn’t idle with FuelTech Automobile Accessories, consider the following: 1. Check TPS calibration. 2. Check timing with a timing light. 3. Examine the TPS idle table and adjustment. 4. Check the O2 sensor reading.
How to troubleshoot FuelTech Automobile Accessories FT450 that doesn’t read cranking?
If your FuelTech Automobile Accessories FT450 doesn’t read cranking, you should: 1. Check the crank trigger and Cam sync connections. 2. Check the sensor gap. 3. Check the diagnostic panel for RPM signal.
What to do if FuelTech FT450 engine spits & sputters?
If your engine spits and sputters when using FuelTech Automobile Accessories, you can: 1. Check the O2 sensor reading. 2. Check ignition calibration and firing order.
Why FuelTech Automobile Accessories ECU won’t communicate to PC?
If your FuelTech Automobile Accessories ECU won’t communicate with your PC: 1. Ensure your software version is compatible with your FT450 firmware version. 2. Check if read and write buttons get colored when FT450 is connected.
Details the connector for DIY expansion to control EFI fuel injectors or accessory activation.
Details the connector for DIY expansion to control ignition or accessory activation.
Details the connector for adding up to two configurable inputs for sensors or buttons.
Details the terms, conditions, and limitations of the product warranty provided by FuelTech.
Specific overview of the FT450 Universal Harness design and purpose.
Detailed pinout and function mapping for the FT450/FT550 A Connector.
Description of the individual components that make up the FuelTech FT450/FT550 Sportsman harness.
Information about optional Smart Coil harness components for ignition system expansion.
Explanation of the automotive-type relays and integrated fuses for system power and protection.
Details on the auxiliary connectors for CAN communication and other functions.
Description of connectors for extra inputs, sensors, and power outputs.
Information on temperature sensor inputs for engine coolant and transmission.
Details on connectors for oil and fuel pressure sensors, including compatible sensor types.
Information about the WB-O2 NANO connector, O2 sensor, and CAN communication.
Details on the Ignition Expansion connector for use with Smart Coil Harnesses.
Description of the safe and user-friendly firewall CPC connector for harness routing.
Details on unterminated wires for Crank Hall effect or Variable Reluctance sensors.
Details on unterminated wires for Cam Hall effect or Variable Reluctance sensors.
Description of the auxiliary power connector for positive and negative battery connections.
Details on FuelTech PS series sensors for fuel and oil pressure measurements.
Information on the engine coolant temperature sensor and its importance for engine operation.
Details on the FuelTech WB-O2 NANO device, its connectors, and analog output configuration.
Information on the Bosch LSU 4.2 Wideband O2 sensor and its compatibility with FuelTech systems.
General| Communication | CAN, USB |
|---|---|
| ECU Type | Standalone |
| Real-time Tuning | Yes |
| Boost Control | Yes |
| Nitrous Control | Yes |
| O2 Closed Loop | Yes |
| Gear Controller | Yes |
| Compatibility | Universal |
| Display | LCD |
| Data Logging | Yes |
| Screen Type | Touchscreen LCD |
| Internal MAP Sensor | Yes |
| Operating Temperature | -20°C to 70°C |
| Display Type | Color LCD |
| Outputs | Multiple |
To Next Page