Need help?Do you have a question about the FujiFilm DryPix 7000 and is the answer not in the manual?
General| Type | Dry Laser Imager |
|---|---|
| Print Technology | Dry Laser Imaging |
| Print Resolution | 320 dpi |
| Resolution | 320 dpi |
| Connectivity | Ethernet 10Base-T/100Base-TX |
| Technology | Laser |
| Print Speed | Up to 180 films/hour |
| Throughput | Up to 180 films/hour |
| Gradation | 12-bit |
| Image Area | 347 x 432 mm (14 x 17 inch) |
| Media Size | 8 x 10, 10 x 12, 11 x 14, 14 x 17 inch |
| Print Size | 8 x 10, 10 x 12, 11 x 14, 14 x 17 inch |
| Film Sizes | 8 x 10, 10 x 12, 11 x 14, 14 x 17 inch |
| Media Type | Dry Imaging Film |
| Dimensions (W x D x H) | 610 x 700 x 1470 mm |
| Weight | 200 kg |
| Power Requirements | 100-240 V AC, 50/60 Hz |
Overview of manual revisions and affected pages.
General safety and procedural warnings before performing maintenance.
Guide on interpreting manual sections and referencing parts lists.
Procedures for removing various external covers of the equipment.
Steps for removing and reinstalling the BCR assembly.
Procedure for removing the main tray loading unit assembly.
Steps for removing the film tray from the equipment.
Procedure for removing the film pack and shutter detection sensor.
Procedure for removing the tray detection switch.
Procedure for removing the tray lock mechanism.
Procedure for removing the guide rails for the tray loading unit.
Procedure for removing the rail components associated with the tray.
Procedure for removing the squeezing roller.
Procedure for removing specific types of screws used in the unit.
Procedure for removing the main removal unit assembly.
Procedure for removing the drive cam component.
Procedure for removing the suction cup arm mechanism.
Procedure for removing the suction cup itself.
Procedure for removing the bellows component.
Procedure for removing the upper conveyor unit.
Procedure for removing the lower film positioning motor (MD6).
Procedure for removing the upper conveyor exit motor (MD2).
Procedure for removing the cleaning roller grip release motor (MD4).
Procedure for removing the lower film positioning assembly.
Procedure for removing the upper film positioning motor (MD5).
Procedure for removing the upper film positioning assembly.
Procedure for removing the conveyor unit exit guide.
Procedure for removing the upper conveyance driving roller.
Procedure for removing the lower conveyance driving roller.
Procedure for removing the conveyor unit guide.
Procedure for adjusting the grip idle gear.
Procedure for removing the lower conveyor unit.
Procedure for removing the sub-scanning unit.
Procedure for removing the sub-scanning motor (ME1).
Procedure for removing the sub-scanning roller.
Procedure for removing the film leading edge detection sensor (SE1).
Procedure for removing and reinstalling the scanner unit.
Procedure for removing the cooling fan assembly.
Procedure for removing the filter section cooling fan.
Procedure for removing the film cooling section.
Procedure for removing the heat development unit.
Procedure for removing the heat development rack assembly.
Procedure for removing the heat development roller.
Procedure for removing the film release unit.
Procedure for removing the density measurement light-emitting board.
Procedure for removing the operation panel.
Procedure for removing the controller assembly.
Procedure for replacing the Hard Disk Drive (HDD).
Procedure for replacing the PC board.
Procedure for replacing the MCT board.
Procedures for replacing and adjusting timing belts in the sorter.
Procedure for adjusting the magnet on the jam removing guide plate.
Steps required before performing version upgrades or full installations.
Step-by-step guide for upgrading the main unit software.
Step-by-step guide for performing a full installation of the software.
To Next Page
