En-34
z
Mode operation
Auto (in cooling model)
• WhenAuto(automaticchangeover)operationrst
selected, the fan will operate at very low speed for about
a few minutes, during which time the indoor unit detects
the room conditions and selects the proper mode.
Roomtemperatureishigherthanthedenedtempera-
tureintemperaturesetting→Coolingmodeordrymode
Roomtemperatureisclosetoorlowerthanthedened
temperatureintemperaturesetting→Monitoroperation
Dened
temperature in
temperature
setting
Cooling mode
or Dry mode
Monitor operation
• When the indoor unit has adjusted your room’s tempera-
ture to near the temperature setting, it will begin monitor
operation. In the monitor operation mode, the fan will
operate at low speed. If the room temperature subse-
quently changes, the indoor unit will once again select
the appropriate operation (cooling) to adjust the tempera-
ture to the value set in the temperature setting.
• If the mode automatically selected by the unit is not what
you wish, select one of the mode operation (Cooling,
Dry, Fan).
Auto [in heating and cooling (Reverse cycle) model]
• When Auto (automatic changeover) is selected, the air
conditioner selects the appropriate operation mode
(cooling or heating) according to your room’s present
temperature.
• WhenAutooperationrstselected,thefanwilloperate
at low speed for about a few minute, during which time
the indoor unit detects the room conditions and selects
the proper operation mode.
Roomtemperatureishigherthanthedenedtemperature
intemperaturesetting→Coolingmodeordrymode
Roomtemperatureisclosetothedenedtemperature
intemperaturesetting→Determinedbyoutdoor
temperature
Roomtemperatureislowerthanthedenedtemperature
intemperaturesetting→Heatingmode
Dened
temperature in
temperature
setting
Cooling or Dry
Heating
Determined by
outdoor temperature
• When the air conditioner has adjusted your room’s
temperature to near the thermostat setting, it will begin
monitor operation. In the monitor operation mode, the
fan will operate at low speed. If the room temperature
subsequently changes, the air conditioner will once again
select the appropriate operation (heating, cooling) to
adjust the temperature to the value set in the thermostat.
• If the mode automatically selected by the unit is not what
you wish, select one of the mode operation (Heating,
Cooling, Dry, Fan).
Heat*
• Use to warm your room.
• When Heating mode is selected, the air conditioner will
operate at very low fan speed for about 3 to 5 minutes,
after which it will switch to the selected fan setting. This
period of time is provided to allow the indoor unit to warm
up before beginning full operation.
• When the room temperature is very low, frost may form
on the outdoor unit, and its performance may be re-
duced. In order to remove such frost, the unit will auto-
matically enter the defrost cycle from time to time. During
Automatic defrosting operation, the Heating operation
will be interrupted.
• After the start of Heating operation, it takes sometime
before the room gets warmer.
Cool
• Use to cool your room.
Dry
• Use for gently cooling while dehumidifying your room.
• You cannot heat the room during Dry mode.
• During Dry mode, the unit will operate at low speed; in
order to adjust room humidity, the indoor unit’s fan may
stop from time to time. Also, the fan may operate at very
low speed when adjusting room humidity.
• The fan speed cannot be changed manually when Dry
mode has been selected.
Fan
• Use to circulate the air throughout your room.
NOTES
*During Heating mode:
Set the thermostat to a temperature setting that is higher
than the current room temperature. The Heating mode will
not operate if the thermostat is set lower than the actual
room temperature.
During Cooling/Dry mode:
Set the thermostat to a temperature setting that is lower than
the current room temperature. The Cooling and Dry modes
will not operate if the thermostat is set higher than the actual
room temperature (in Cooling mode, the fan alone will oper-
ate).
During Fan mode:
You cannot use the unit to heat or cool your room.
z
Automatic restart
In Event of Power Interruption
• Should the power supply to the air conditioner be inter-
rupted by a power failure, the air conditioner will restart
automatically in the previously selected mode once the
power is restored.
• Use of other electrical appliances (electric shaver, etc.) or
nearby use of a wireless radio transmitter may cause the
air conditioner to malfunction. In this event, temporarily
disconnect the power supply, reconnect it, and then use
the remote controller to resume operation.
9381067145_OM_EN.indd 34 14/09/2015 13:48:08
To Next Page
Loading...
Need help?
General
