What does 'Previous boot incomplete' mean on my Fujitsu LifeBook T732 Tablet?
If you see 'Previous boot incomplete - Default configuration used' on your Fujitsu Tablet, it means that due to an error during the previous system boot, default values were used for certain settings. Press the F1 function key when prompted to do so.
Why won't my Fujitsu LIFEBOOK Tablet PC work on battery alone?
If your Fujitsu LIFEBOOK Tablet PC won't operate on battery, the installed battery may be dead or faulty. Replace it with a charged one or install a power adapter. If no battery is installed, install a charged battery. Ensure the battery is properly connected by reinstalling it, and verify its condition using the Status Indicator panel, replacing any shorted battery.
What to do if my Fujitsu display won’t turn on after resuming?
If your Fujitsu display won’t turn on after resuming, check the status indicator panel to verify that the Security icon is blinking, which indicates the system may be password-protected.
Why doesn't the battery indicator illuminate on my Fujitsu Tablet?
If the battery indicator on your Fujitsu Tablet does not illuminate, it could be due to a couple of reasons. First, ensure that the battery is correctly installed in its compartment. If the battery is fully discharged, charge the battery, install a charged battery, or connect the notebook to a mains outlet using the mains adapter.
What to do if my Fujitsu LifeBook T732 stops working?
If your Fujitsu Tablet stops working, it might be in energy-saving mode, so try leaving energy-saving mode. Alternatively, an application program may have caused the malfunction. In this case, close the application program or restart the notebook by restarting the operating system or switching the device off and back on again. Finally, if the battery is dead, charge the battery, insert a charged battery, or connect the mains adapter to the notebook.
Why does my external monitor remain blank when connected to my Fujitsu Tablet?
If the external monitor remains blank when connected to your Fujitsu Tablet, make sure the monitor is switched on. If it is on, power saving may have been activated, so press any key to continue. Also, check the brightness setting on the monitor and adjust it if it's too dark. If the screen output is set to the notebook’s LCD screen, you will need to press the key combination to switch the screen output. Finally, ensure that both the power and data cables are properly connected to the monitor and the notebook.
Why does the battery on my Fujitsu LifeBook T732 discharge too quickly?
If the battery on your Fujitsu Tablet discharges too quickly, it may be because the battery is either too hot or too cold. In this case, bring the notebook up/down to a normal temperature again. If the operating time of the battery life is extremely short, the battery is probably too old; replace the battery if necessary. Also, an application running may consume a great deal of power due to frequent accessing of the hard disk or optical drive, so use the mains adapter as frequently as possible. Finally, the maximum brightness may have been set for the screen. Set the screen slightly darker with the key combination for Decreasing the screen brightness in order to reduce the amount of power being drawn.
Why is my external monitor blank or the image unstable with my Fujitsu LifeBook T732 Tablet?
If the external monitor is blank or the image is unstable when connected to your Fujitsu Tablet, the wrong external monitor may have been selected, or the wrong screen resolution has been set for the application program. Terminate the application program in Windows by pressing Alt + F4. If the fault persists after closing the program, use the key combination for switching the screen output to switch over to the notebook’s LCD screen. Change the screen resolution as described in the documentation for your operating system. Select monitor 1 or 2 as described in the documentation for your operating system.
Why is the battery indicator not illuminating on my Fujitsu Tablet?
If the battery indicator on your Fujitsu Tablet isn't lighting up, it could be due to a couple of reasons. First, ensure the battery is correctly installed in its compartment. If it is, the battery may be fully discharged. Try charging the battery, installing a charged battery, or connecting the tablet to a mains outlet using the mains adapter.
What to do if my Fujitsu Tablet suddenly stops working?
If your Fujitsu Tablet stops working, there are a few potential causes. It might be in energy-saving mode, so try leaving energy-saving mode. An application program may have caused a malfunction, so try closing the application or restarting the tablet (either by restarting the operating system or switching the device off and back on again). Also, the battery may be dead, so try charging it, inserting a charged battery, or connecting the mains adapter.
General| Form factor | Convertible (Swivel) |
|---|---|
| Product type | Hybrid (2-in-1) |
| Product color | Black, Silver |
| Bus type | DMI |
| Stepping | L1 |
| Tjunction | 105 °C |
| Processor cache | 4 MB |
| Processor cores | 2 |
| Processor model | i7-3520M |
| System bus rate | 5 GT/s |
| Processor family | Intel® Core™ i7 |
| Processor series | Intel Core i7-3500 Mobile series |
| Processor socket | BGA 1023 |
| Processor threads | 4 |
| Processor codename | Ivy Bridge |
| Processor frequency | 2.9 GHz |
| Processor cache type | Smart Cache |
| Processor lithography | 22 nm |
| Processor manufacturer | Intel |
| Processor front side bus | - MHz |
| PCI Express slots version | 3.0 |
| Processor boost frequency | 3.6 GHz |
| Processor operating modes | 64-bit |
| ECC supported by processor | No |
| PCI Express configurations | 1x8, 1x16, 2x4, 2x8 |
| Thermal Design Power (TDP) | 35 W |
| CPU multiplier (bus/core ratio) | 29 |
| Maximum number of PCI Express lanes | 16 |
| Motherboard chipset | Intel® QM77 Express |
| Memory slots | 2x SO-DIMM |
| Internal memory | 4 GB |
| Memory clock speed | 1600 MHz |
| Memory form factor | SO-DIMM |
| Internal memory type | DDR3-SDRAM |
| Maximum internal memory | 16 GB |
| Memory layout (slots x size) | 2 x 2 GB |
| HDD speed | 5400 RPM |
| HDD interface | SATA |
| Storage media | HDD |
| Optical drive type | - |
| Card reader integrated | Yes |
| Total storage capacity | 320 GB |
| Compatible memory cards | SD, SDHC, SDXC |
| Number of HDDs installed | 1 |
| Display surface | Matt |
| Display diagonal | 12.5 \ |
| Touchscreen type | Capacitive |
| Display brightness | 300 cd/m² |
| Display resolution | 1366 x 768 pixels |
| Native aspect ratio | 16:9 |
| On-board graphics card ID | 0x166 |
| Discrete graphics card model | Not available |
| On-board graphics card model | Intel® HD Graphics 4000 |
| On-board graphics card family | Intel® HD Graphics |
| On-board graphics card base frequency | 650 MHz |
| On-board graphics card dynamic frequency (max) | 1250 MHz |
| Front camera resolution | 1920 x 1080 pixels |
| Wi-Fi standards | 802.11a, 802.11b, 802.11g |
| Bluetooth version | 4.0 |
| Ethernet LAN data rates | 10, 100, 1000 Mbit/s |
| Charging port type | DC-in jack |
| USB 2.0 ports quantity | USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them. |
| eSATA/USB 2.0 ports quantity | 0 |
| Pointing device | Touchpad |
| Keyboard number of keys | 84 |
| Bundled software | Adobe Reader, CyberLink PowerDirector, CyberLink PowerDVD, CyberLink YouCam |
| Processor code | SR0MU |
| Processor ARK ID | 64893 |
| Processor package size | 37.5 x 37.5 (rPGA988B); 31.0 x 24.0 (BGA1023) mm |
| Supported instruction sets | AVX |
| Intel Identity Protection Technology version | 1.00 |
| Battery capacity | 72 Wh |
| Battery life (max) | 9.8 h |
| AC adapter power | 80 W |
| AC adapter frequency | 50 - 60 Hz |
| AC adapter input voltage | 100 - 240 V |
| AC adapter output current | 4.22 A |
| AC adapter output voltage | 19 V |
| Password protection type | BIOS, HDD |
| Storage relative humidity (H-H) | 8 - 85 % |
| Operating relative humidity (H-H) | 20 - 85 % |
| Sustainability certificates | ENERGY STAR |
Weight and Dimensions| Depth | 233 mm |
|---|---|
| Width | 316 mm |
| Height | 38 mm |
| Weight | - g |
Explains the primary power sources available for the LIFEBOOK Tablet PC.
Instructions for connecting AC and Auto/Airline adapters for power.
Steps for powering on the system, including boot sequence and initial setup.
Features and options for conserving battery power and managing system power states.
Details on the rechargeable Lithium ion battery, its charging, and status indicators.
Instructions for installing and removing SD cards for data storage.
Guidance on installing and removing ExpressCards for expanded functionality.
Steps for installing additional memory modules to increase system capacity.
Information on the optical drive, media player software, and handling media discs.
Overview of the various ports for connecting external devices.
General guidance for diagnosing and resolving common setup or operating problems.
A systematic procedure to follow before pursuing complex troubleshooting steps.
A table listing common problems, their causes, and solutions.
Steps to restore the system image and software for Windows 7.
Tips and guidelines for maintaining the LIFEBOOK Tablet PC and its devices for longevity.
Instructions on how to properly clean the exterior, keyboard, and LCD display.
Procedures for cleaning the system's dust filter to maintain optimal cooling.
Guidelines for storing the Tablet PC for extended periods.
Recommendations for safely transporting the Tablet PC.
Details the hardware and environmental specifications for the Fujitsu LIFEBOOK Tablet PC.
Introduces the optional integrated Wireless LAN Mini-PCI device and its setup.
Explains different wireless LAN modes like Ad Hoc and Infrastructure.
Provides causes and countermeasures for common wireless LAN connection issues.
Lists the technical specifications for the WLAN device.
Defines Bluetooth technology and its use in creating Personal Area Networks (PANs).
Introduces the fingerprint sensor for enhanced system security and user authentication.
Guides through preparation and installation of the OmniPass fingerprint recognition application.
Steps for installing the OmniPass application, including system requirements.
To Next Page
