Fujitsu Primergy RX300 S3 Start Guide

1
3
Installing internal options
If internal options have been purchased separately, install them before installing the operating system.
In the following case, it is not required to install the internal options.
- Custom Made Service
1
Checking the items
supplied
Check the contents in the package using
the "Contents List".
If any items are missing, contact an ofce listed
in the "Contact Information".
n
PRIMERGY RX300 S3 Manuals
Manuals for this server can be accessed from the section below of the PRIMERGY Document & Tool CD.
[CD-ROM Drive] :\MANUAL\INDEX.PDF
Manuals can be displayed using Acrobat
®
Reader
®
or Adobe
®
Reader
®
. If using Acrobat
®
Reader
®
, use version 5.0 or later.
2
Reading and understand-
ing "Safety Precautions"
Before using this server, be sure to read and un-
derstand the attached "Safety Precautions".
Also check it when connecting, installing internal options
and setting up this server.
n
Point to note before installing internal
options
When installing internal options, perform operations after
reading the following manuals.
"Chapter 7 Installing Internal Options"
"PRIMERGY Server Books"/"Supplement"
Install the OS before installing the following options.
Installing the OS after options have been installed will
cause installation operations to end in an error.
- Non-system hard disks
- External SCSI optional devices (Hard disk cabinet,
Backup cabinet, DAT unit , etc.)
n
Available Internal options and
installation locations









After installing internal options, check that the order and
place of installation is correct and cables are correctly at-
tached.
RX300 S3
B7FH-4301-01EN-00

Fujitsu Primergy RX300 S3 Specifications

General

Tcase	78 °C
Bus type	FSB
FSB Parity	Yes
Processor cache	4 MB
Processor cores	2
Processor model	5080
Processor series	Intel Xeon 5000 Series
Processor socket	LGA 771 (Socket J)
Processor threads	4
Processor codename	Dempsey
Motherboard chipset	Intel® 5000P
Processing Die size	162 mm²
Processor frequency	3.73 GHz
Processor cache type	L2
Processor lithography	65 nm
Processor system type	DP
Processor manufacturer	Intel
Processor package size	37.5 x 37.5 mm
Processor front side bus	1066 MHz
Processor operating modes	64-bit
ECC supported by processor	No
Thermal Design Power (TDP)	130 W
Processor core voltage (AC)	1.25 - 1.40 V
CPU multiplier (bus/core ratio)	14
Number of Processing Die Transistors	376 M
Maximum graphics card memory	8 MB
Memory slots	8
Internal memory	2 GB
Internal memory type	DDR2-SDRAM
Maximum internal memory	32 GB
Memory layout (slots x size)	2 x 1 GB
Networking features	Ethernet/Fast Ethernet/Gigabit Ethernet
Expansion slots	1 x PCIe x8, 2 x PCIe x4, 2 x PCI-X
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Noise level	56 dB
Chassis type	Rack (2U)
Compatible operating systems	Windows Server 2003, Novell SUSE Linux Enterprise Server, Red Hat Enterprise Linux, VMware ESX
I/O ports	8 x SAS
Power supply	600 W
Power requirements	100 - 240V, 50/60 Hz
Operating temperature (T-T)	10 - 35 °C
Safety	IEC 60950-1, EN 60950-1
Electromagnetic compatibility	EN 55 022 A, EN 55024, EN 61000-3-2 / -3-3
RAID levels	1, 5, 10, 50
Processor ARK ID	27213

Weight and Dimensions

Depth	785 mm
Width	483 mm
Height	86 mm
Weight	25000 g