12-24 VDC
000-144-422
(5m) cable
supplied
w/BBFF1
NAVNET QUICK SETUP GUIDE 7 inch series, single display (with optional equipment shown)
OR
cable included/attached
to the BBWGPS
Use supplied GP32 cable
(I/O) and part # 000-144-418
cable to connect
12-24 VDC
BBFF1 SOUNDER
12-24 VDC
000-125-237 cable
supplied with PG1000
or use a # 000-117-603
cable to connect to a
external heading device
Heading device (optional)
Furuno PG1000
OR
other external
(required for overlay)
AD10 Furuno format
required for ARP11
radar autoplotter option
FURUNO GP32
OR
other external GPS
Radar antenna
connection
(GP1700C, N/A)
BBWGPS (only configure if the BBWGPS antenna is connected to DATA1)
1. Press "MENU", Select [SYSTEM CONFIGURATION], Select [NAV OPTION]
2. Select [NAV SOURCE SETTINGS], Change POSITION SOURCE to [FURUNO BB GPS]
3. Press "RETURN"
4. Select [GPS SENSOR SETTINGS], Select [WAAS SETUP], Set [WAAS MODE], [ON]
5. Press "RETURN" three times
6. Select [SYSTEM SETUP], Select [PORT SETUP], Select [GPS/NMEA PORT] , Set FURUNO GPS SENSOR to [YES]
7. Press [RETURN], then [MENU] for normal operations
STEP 1
(Confirm no simulator modes are selected [SIM] would be displayed in upper left corner of display)
Connect the GPS position source. Use the Furuno BBWGPS antenna, Furuno GP32 or any compatible external device
(must output NMEA sentences GGA, VTG, ZDA, see manufacturer specifications).
RADAR SETUP PROCEDURES:
NOTE: Installation Menu access required.
Press and hold [MENU] while powering on display (starts normally)
Press [MENU], [SYSTEM CONFIGURATION], [INSTALLATION SETUP]
Press [RADAR SETUP] these are REQUIRED ADJUSTMENTS!
ANTENNA TYPE
A 1722 / 1722C
B 1732 / 1732C
C 1742 / 1742C
F 1762 / 1762C
ANTENNA ROTATION [ROTATE] (do not change)
TRANSMIT RADAR FOR 5 minutes prior to and continue for FOLLOWING
PROCEDURES (on the shortest range, set gain & sea control properly)
TUNING [OFF] Press [EDIT], select [ON], Press [ENTER], when complete
"NOW TUNING" disappears.
TIMING ADJUST [OFF] Press [EDIT], select [ON], visually select long straight
target, rotate knob to straighten target, Press [ENTER].
HEADING ADJUST (NOTE: factory setting 180° out for 24" dome antennas)
select [NEXT PAGE], HEADING ADJUST [OFF], Press [EDIT], select [ON], using
a range between 0.125-.25nm, rotate knob to bisect radar target, Press [SET]
Maximum radar ranges may need to be turned on using [MENU],
[RADAR RANGE SETUP], after "ANTENNA TYPE" is changed
DATA 2
DATA 1
NETWORK
DATA 3 output to
optional autopilot
or other device is
available, see wiring
configurations page
(7" display NOTES)
Connect the radar antenna to DJ1 of the radar display 1722/C, 1732/C,
1742/C or 1762/C
use the NavNet display "default" menu settings if connecting
an external GPS device (example: Furuno GP32 shown)
BBWGPS
STEP 2
Applies to Radar only (Omit if installing a plotter)
POWER OFF then ON after any "MENU CHANGES" to store the new information.
Refer to the "Wiring configurations (7 inch display notes)" or "General Information" page for details
Connect the BBFF1 network sounder to the display "network port" using the
supplied blue 000-144-422, 5m network cable
STEP 3
BBFF1 Network sounder if Installed (Plug and Play)
BBFF1(if installed): Displaying digital temperature and depth on NavNet display(s)
Press [MENU], [SYSTEM CONFIGURATION]
[GENERAL SETUP] (default is [NMEA] for displaying input from external depth and temperature devices)
TEMPERATURE SOURCE [ETR] (transducers with temperature sensor only)
DEPTH SOURCE [ETR]
To Next Page
Loading...
