Furuno FS-2550 User Manual

GMDSS Equipment
S
y
stem settin
g
s list
FS-1562
FS-75/2550
FS-5000/8000
DSC-5
DSC-6
DSC-8V
DSC-60
AA-50
DP-5
DP-6
FM-7000
FM-7500
FM-8000
FM-8500
FM-8700
DMC-5
FELCOM 10
FELCOM 11
FELCOM 12
FELCOM 80
FELCOM81
FELCOM82
REMOTE STATION
NX-500
IB-581
IB-582
TCE-59060-D
(J58-19110-0)
(0208, NAYO)

Furuno FS-2550 Specifications

General

Power Output	150W PEP
Tuning Steps	10 Hz
Power Supply	13.8 VDC
Frequency Range (Transmit)	1.6 - 27.5 MHz
Frequency Range (Receive)	0.1-30 MHz
Emission Modes	J3E, H3E, F1B, A1A

Summary

Instructions for Canceling Distress Alert

VHF DSC

Procedure for canceling VHF distress alerts, including switching off transmitter and broadcasting.

MF DSC

Procedure for canceling MF distress alerts, including tuning to radiotelephony on 2182 kHz.

HF DSC

Procedure for canceling HF distress alerts across multiple frequency bands.

Inmarsat C

Procedure for canceling Inmarsat C distress alerts via appropriate RCC.

EPIRB

Procedure for canceling EPIRB distress alerts, contacting nearest coast station.

MF/HF SSB Radiotelephone FS-1562-15/25

MF/HF SSB Radiotelephone FS-75/2550

2.1 Procedure

3. Channel Programming

Procedure for programming radio channels.

4. Power Data Setting

Configuration of power data settings for the equipment.

MF/HF SSB Radiotelephone FS-5000/8000

3. Jumper settings

Configuration of the system via jumper settings.

4. User (Preset) Channel Programming

Procedure for storing user-defined channels.

5. Power Adjustment

Procedures for adjusting the output power levels.

DSC Terminal DSC-5

2. Changing System Settings and MMSI number

Procedure to modify system settings and MMSI number.

2.1 Changing system settings

3. Jumper wire settings

Configuration of the unit via jumper settings.

9. Power and Frequency measurement of VHF Radiotelephone

Procedure to measure power and frequency of VHF radiotelephone.

DSC Terminal DSC-6/6A

3.1 Initial settings

3.2 Changing System settings

Procedure for modifying system settings.

5. Jumper setting

Configuration of the unit via jumper settings.

6. Changing ID (MMSI) number

Procedure for changing the MMSI number.

11. Power and Frequency measurement of MF/HF Radiotelephone

Procedure to measure power and frequency of MF/HF radiotelephone.

DSC Terminal DSC-8V/8VP

2. Changing system settings

Procedure for modifying system settings.

4. Jumper wire setting

Configuration of the unit via jumper wire settings.

8. Power and Frequency measurement of VHF Radiotelephone

Procedure to measure power and frequency of VHF radiotelephone.

DSC Terminal DSC-60

2.1 Setup menu: [#/SETUP]

3. Setting DIP Switches

Configuration of the unit via DIP switches.

5. How to enter MMSI

Procedure for entering the MMSI number.

6. Self test

8. Power and Frequency measurement of MF/HF Radiotelephone

Procedure to measure power and frequency of MF/HF radiotelephone.

9. How to update system program

Procedures for updating the system program.

MF/HF Watch Receiver AA-50

2. Connection

Describes the physical connection of the AA-50 receiver.

3. Jumper setting

Configuration of the unit via jumper settings.

NBDP DP-5

3.2 Terminal settings (F6)

Terminal configuration options accessed via the F6 key.

3.3 System settings (F8)

System configuration options accessed via the F8 key.

4.2 Changing F6 and F8 settings

NBDP DP-6

3. Initial settings

3.1 Answerback code and ID code entry

Procedure for entering answerback code and ID.

3.2 System settings (F6)

System configuration options accessed via the F6 key.

4. Changing AAB, ID code and System settings

Modifying Answerback code, ID code, and system settings.

4.1 Changing Answerback code and ID code

Procedure for changing the Answerback code and ID.

4.2 Changing F6: System settings

5. Self Test

6. How to Update Programs

Procedures for updating the unit's programs.

6.1 Terminal Program

6.2 Main: Main Unit Program

VHF Radiotelephone FM-7000

2.1 System setting Jumper Connections

Configuration via jumper connections on the panel and boards.

2.2 Disabling/enabling ATIS

VHF Radiotelephone FM-8000

2. System Settings

Details on configuring system parameters and settings.

2.1 Changing System setting

2.2 Channel Preset (CH0 to CH255 available)

Procedure for programming channels from CH0 to CH255.

3. Adjustment

Procedures for adjusting equipment parameters.

3.1 Tx Power Adjustment

Procedure for adjusting the transmitter power output.

3.2 Frequency Adjustment

Procedure for adjusting the operating frequency.

VHF Radiotelephone FM-8500

4. Jumper Setting

Configuration of the unit via jumper settings.

VHF Radiotelephone FM-8700

2.1 Initial Settings

2.2 Changing system settings (Protection ON/OFF)

Modifying system settings, including protection ON/OFF.

4. Jumper settings

Configuration of the unit via jumper settings.

5. Changing ID (MMSI) and Private mode

Procedure for changing ID (MMSI) and private mode settings.

6. Adjustment

Procedures for adjusting equipment parameters.

6.1 TX Power Adjustment

Procedure for adjusting the transmitter power output.

6.2 TX Frequency Adjustment

Procedure for adjusting the transmitter frequency.

8. Self test

10. Power and Frequency measurement of VHF Radiotelephone

Procedure to measure power and frequency of VHF radiotelephone.

Distress Message Controller DMC-5

4. Self test

INMARSAT C FELCOM 10

2.2 Terminal setup: [F6]

3. Jumper wire setting

Configuration of the unit via jumper wire settings.

INMARSAT C FELCOM 11

2.1 System setup: [F5]

2.2 Terminal: [F6]

2.3 Updating a Distress Alert: [F10]

Procedure for updating distress alert information.

9. How to up date the Terminal (IB-581) program

Procedure for updating the terminal program.

INMARSAT C FELCOM 12

2.1 System: [F8]

2.2 Updating a Distress Alert: [F8]

Updating distress alert information via the F8 key.

3. Dip switch setting

Configuration of the unit via DIP switches.

7. How to update the Terminal and CPU-2 program

Procedures for updating terminal and CPU-2 programs.

7.1 Terminal

7.2 CPU-2

INMARSAT B FELCOM 80

3.1 DIP switch setting (Antenna unit: IB-180)

Setting DIP switches on the antenna unit.

3.2 Tx IF output level setting (Communication unit: IB-280)

Setting the Tx IF output level.

3.3 Gyro Converter setting (Communication unit: IB-280)

Setting the Gyro converter.

3.7 Terminal settings

Configuration settings for the terminal.

5. How to update Terminal Program

Procedure for updating the terminal program.

INMARSAT B FELCOM 81

3. Setting procedure

3.1 Adjustment of limit switch (Antenna unit: IB-181)

Adjusting the limit switch on the antenna unit.

3.2 Tx RF output Level setting (Communication unit: IB-281)

Setting the Tx RF output level.

3.5 Terminal settings

Configuration settings for the terminal.

4. Self Test

5. How to update the Terminal program

Procedure for updating the terminal program.

INMARSAT B FELCOM 82

2. System settings

Details on configuring system parameters and settings.

2.1 Heading alignment

Procedure for aligning the heading direction.

2.2 Telephone setting

2.4 Gyro setting

2.5 Setup NAV data input circuit

2.6 Entering answer back code (only for class-1)

Procedure for entering answerback code.

2.7 OID/DID setting

Procedure for setting Originating and Destination IDs.

2.8 HSD set up

2.10 Returning settings to factory defaults

3. Self-test

3.4 Distress alert test (FUNC683)

Procedure for testing the distress alert function.

4. Program Update

4.1 Connection

4.2 Upgrading SYSTEM, DEMOD, SYNC, DECODE, and TERM programs

Updating various system programs.

4.3 Upgrading handset program

REMOTE STATION RB-700

2. RB-700

3. RB-500 : C.Loop

3.4 Connection

NAVTEX RECEIVER NX-500

1. Connection

Describes the physical connection of the NX-500 receiver.

2. Slide switch settings

3. System settings

Details on configuring system parameters and settings.

5. Self test

TERMINAL UNIT IB-581

2. Changing the Terminal Software

Procedures for changing the terminal software.

2.2 A method to change the terminal program by formatting A-drive

3. Installing PC-DOS

3.4 Backup the System Files (PC-DOS: Ver. 6.3)

3.5 Changing BIOS (Basic Input Output System) settings

3.6 Changing DIP SW and Internal Connector

3.7 Installing System Files

4. How to erase password

TERMINAL UNIT IB-582

1. DOS installation

1.1 How to copy DOS program

1.2 DOS installation

2. Erasing password

REMOTE STATION RB-500

2. RB-700 : C.Loop

2.1 Priority settings

2.2 Jumper settings

3. RB-500

3.1 Jumper settings

4. DB-500

4.1 Connection

4.3 RB-500/700 Connection

4.4 FS-1562 and DSC/DP Connection

5. Jumper settings on MAIN Board