FUTABA 10CAG User Manual

36
Second aileron (
AILE-2
) (
ACRO

GLID 1A+1F

GLID 2A+1F
only): changes the default choice for dual aileron servos from
channels 6 (
FLAPERON
) to channels 5 and 6 or channels 3 and 6 (
GLID 1A+1F
only), or 7 (
AIL-DIF
) to channels 5 and 7.
NOTE: Changing
AILE-2
only tells the system which servos to utilize if
FLAPERON
or
AIL-DIF
is activated. You still must
activate that function and complete its setup. For details on twin aileron servos, including using
AILE-2
, see p. 55.
(
GLID 1A+1F
only): If using channel 3 for second aileron, the receiver's Battery Fail-Safe function does not work.
Adjustable travel limit (
ATL
): makes the channel 3 TRIM LEVER (THROTTLE TRIM) effective only at low throttle,
disabling the trim at high throttle. This prevents pushrod jamming due to idling trim changes. This function defaults to
ON
.
If you are not using channel 3 for throttle, you may want trim operation the same as on all other channels. To do so, set
ATL
to
OFF
. If you need the
ATL
to be effective at the top of the stick instead of the bottom, reverse the
THR-REV
setting. Note
that this affects all models in the radio, not just the model you are currently editing. See servo
REVERSE
, p. 38.
GOAL of EXAMPLE: STEPS: INPUTS:
Change
ATL
from
ON
to
OFF
for battling
robots, tanks, airbrakes and other
channel 3 uses.
Open
BASIC
menu, then open
PARAMETER
submenu.
for 1 second.
(If
ADVANCE
, again.)
to 2nd page of menu.
C
to
PARAMETER
.
Go to
ATL
and Change. (Ex: to
OFF
)
C
to
ATL
. to
OFF
.
Close.
Where next? Set up
ELEVON
IRUWDQNVW\OHFRQWUROWKURWWOHVWHHULQJRQRQH67,&.VHHS
Set up
IDLE-DOWN
and
THR-CUT
to adjust channel 3 servo at low-stick: see p. 40.
5HDVVLJQDX[LOLDU\FKDQQHOVH[IURPGLDOWRVZLWFKVOLGHUVHHS
Utilize servo
REVERSE
: see p. 38.
Adjust servo travel with
END POINT
: see p. 39.
6HWXSGXDOWULSOHUDWHVDQGH[SRQHQWLDO
D/R
,
EXP
): see p. 42.
LCD screen adjustment (
CONTRAST

BACK-LIGHT
):
Adjustability:
The following LCD screen adustments are possible.
• Contrast adjustment
• Backlighting brightness adjustment
CONTRAST
: adjust the LCD contrast from +10(dark) to -10(bright). Also, it is
possible to adjust the contrast from the home screen. See Adjusting Display
Contrast, p.16.
BACK-LIGHT MAX
DGMXVWVWKHEDFNOLJKWLQJEULJKWQHVVIRUWKHVSHFL¿FSHULRGDSSUR[LPDWHO\VHFRQGVDIWHURSHUDWLQJWKH
edit keys. Setting range: OFF(0) to 20(bright).
BACK-LIGHT MIN
DGMXVWVWKHEDFNOLJKWLQJEULJKWQHVVDIWHUWKHDERYHVSHFL¿FSHULRG6HWWLQJUDQJH2))WR
MAX
setting.
GOAL of EXAMPLE: STEPS: INPUTS:
Change
CONTRAST
from
0
to
+2
. Open BASIC menu, then open
PARAMETER
submenu.
for 1 second.
(If
ADVANCE
, again.)
C
to
PARAMETER
.
Go to
CONTRAST
and change setting.
(Ex:
+2
)
C
to
CONTRAST
.
to
+2
.
Close.
Throttle Reverse (
THR-REV
) (
GLID

only): is a special function that reverses the throttle control, including moving the trim
functionality to the stick's upper half.
The separate
THR-REV
settings for each model can be set. Default setting depends on the
THR-REV
setting in the
TX SETTING
menu, see p.17.

FUTABA 10CAG Specifications

General

Brand	FUTABA
Model	10CAG
Category	Remote Control
Language	English