FUTABA 8UAFS - Glossary

To Next Page

To Previous Page



The abbreviations used with the 8UA are defined below alphabetically. Related pages are

given in parenthesis following the definition ().

→ →

Main Page

Flying Safety4
Table of Contents7
Transmitter9
Receiver9
Servos9
Specifications10
Additional Accessories10
Transmitter Controls - Aircraft11
Switch Assignment Table12
Charging the Ni-CD Batteries13
Adjusting the Lengh of the Non-Slip Control Sticks13
Stick Lever Tension Adjustment14
Changing the 8UA Transmitter's Mode14
Receiver and Servo Connections15
Receiver Note15
Radio Installation16
Servo Mounting16
Servo Throw16
Switch Harness Installation16
Airplane Frequencies17
Transmitter Displays and Buttons18
Startup Screen18
Edit Keys18
Warning and Error Displays19
Backup Error19
Model Selection Error19
Low Battery Error/Mixer Alert Warning19
Memory Module Initialize Display20
RF Module Warning20
Aircraft (ACRO) Menu Functions22
Map of ACRO Aircraft Functions23
Aircraft Setup Instructions25
Pattern Aircraft Flight Trimming Chart27
ATV - Adjustable Travel Volume29
D/R - Dual Rates29
Setting ATV on Your System29
Setting Dual Rate Values and Switches30
EXP - Exponential Settings31
Setting Exponential Values31
IDL - DN - Idle down Function32
F/S - Fail Safe Function (PCM Mode Only)32
REVERS - Servo Reversing34
Setting the Failsafe Function34
PARA - Parameter Menus35
DATA RSET - Data Reset (para Function)35
ATL - Adjustable Travel Limit (para Function)35
Resetting the Memory35
EG/S - Engine Starter (para Function)36
TYPE - Model Type (para Function)36
MOD - Modulation Select (para Function)38
AIL2 - Second Aileron (para Function)38
Changing Your Transmitter’s Modulation38
TRAINR - Trainer Functions39
Trainer Function Operation Modes39
Setting up Trainer Mode39
MODEL - Model Function40
SEL - Model Select (Model Function Submenu)40
COPY - Copy Menu (Model Function Submenu)40
Choosing Another Model Memory to Load40
NAME - Model Name (MODEL Function)41
Copying from One Model Memory to Another41
Model Naming Instructions41
TRIM - Trim Settings42
RSET - Trim Reset (TRIM Function Submenu)42
STEP - Trim Step (TRIM Function Submenu)42
DISP - Trim Reverse Display (TRIM Function Submenu)43
SUBTRM - Subtrim Settings43
TH-CUT - Throttle Cut Function44
Timer (Stopwatch Function)44
Setting up Throttle Cut Operations44
Using the 8UA Timer Function45
Aircraft (ACRO) Advance Menu Functions46
PMIX - 1-7 - Programmable Mixers 1-747
FLPRON - Flaperon Mixing49
Setting up the Flaperon Function49
FLAPTRM - Flap Trim (Camber)50
AI-DIF - Aileron Differential50
ABRAKE - Airbrake Function51
ELE-FL - Elevator-To-Flap Mixing52
V-Tail Mixing52
ELEVON - Elevon Mixing53
ALVATR - Ailevator Mixing53
SNP - Snap Roll54
Setting up Dual Elevator Servos54
TH-DLY - Throttle Delay55
TH-NDL - Throttle Needle Mixing55
Glider (GLID1FLP/2FLP) Advance Menu Functions56
8UA Glider (GLID1FLP, GLID2FLP) Functions Map57
GLID-2FLP Setup Instructions (Two Aileron and Two Flap Servos)58
Sailplane Trimming Chart61
BFLY — Butterfly Mixing (“Crow”)63
Butterfly Mixing Programming63
FLP-AI: Flap - Aileron Mixing64
AIL-FL - Aileron - Flap Mixing65
Start (Launch) Presets66
Speed Presets67
Helicopter Basic Menu Functions68
Helicopter Setup Instructions70
Flight Condition Switching71
Helicopter Flight Trimming Chart73
TH-CRV - Throttle Curve (Normal)74
PI-CRV - Pitch Curve (Normal)75
REVOLU - Revolution Mixing (Normal)76
SWASH - Swash AFR77
INVERT - Inverted Flight Function78
TH-CUT - Throttle Cut79
Helicopter (HELISWH1/SWH2) Advance Menu Functions80
TH-CRV - Throttle Curve (Normal, Idle-Up 1, Idle -Up 2)81
Normal Curve Adjustment Method81
Idle-Up 1 and 2 Curve Adjustment Method81
Inputting the Throttle Curve in Normal, Idle-Up 1, and Idle-Up 282
TH-HLD - Throttle Hold83
Rudder Offset at Throttle Hold83
OFST-1-2-IV - Offset 1, 2 and IV84
Delay Function84
PMIX-1-2 - Programmable Mixers 1-285
Mixer Initial Settings85
HOV-TH - Hovering Throttle87
HOV-PI - Hovering Pitch87
GYRO - Gyro Mixing88
Govrpm - Governor Mixing88
TH-NDL - Throttle-Needle Mixing (Normal, Idle)90
INVERT CROSS - Inverted Cross Position91
REVOLU - Revolution Mixing (Normal, Idle-Up 1, Idle-Up 2)91
Revolution Mixing for Idle-Up 1 and 291
Inputting Revolution Five-Point Curves92
PI-CRV - Pitch Curve (Normal, Idle-Up 1 and 2, Hold, Inverted)93
Normal Curve Adjustment93
Idle-Up 1 and Idle-Up 2 Curve Adjustment93
Throttle-Hold Curve Adjustment93
Handling the Campac95
Compatibility of 8Usuper Series and Old 8U Series Data Packs95
Back-Up Unnecessary95
Glossary96
Aircraft (ACRO) Data Sheet98
Glider (GLID) Data Sheet100
Helicopter (HELI) Data Sheet101

FUTABA 8UAFS - Glossary

Table of Contents

Related product manuals