Gallo Tech GStarter I - Programming Function Set up Options

© Copyright
Gallo Technologies
. All Right Reserved
-
5
-
52008
Lock/Unlock siren
Chirp
:
If this option is set to
DISABLE
the sire
n will not chirp when locking and unlocking the
doors.
Two Pulse Locking / unlocking
:
When pressing
or
the electrical pulse sent to the door
locking/unlocking mechanism can be set at either one pulse or two pulses. Most vehicles only require one pulse
(factory default). Some
vehicles
require one pulse to unlock the
driver’s
door only and a second pulse to unlock all
doors. If this is the case and you want all doors to be unlocked at the same time
,
set this option to two pulses.
OR,
setting to one
pulse will unlock the driver’s door on the first unlock button push then unlock all doors on the second
push.
*
Ignition Key Start
F
unction:
If this option is set to
ENABLE
(factory default) the
vehicle
can be started by
using either the ignition key or
the
ENGINE START
push button. If this option is set to
DISABLE
the
vehicle
can be
started with the
ENGINE START
push button only.
*
Disable Start
Button
Cut Off Delay
:
If this option is set to
ENABLE
(factory default) the
vehicle
can be started
after th
e ignition key is turned
ON
and there will be no start button cut off delay.
*
30 Second
S
tart
Button
Cut Off
D
elay
:
If this option is set to
ENABLE
the
vehicle
can not be started 30
seconds after the ignition key is turned
ON
. Recycling the ignition key
OFF
to
ON
will reset the time delay for
another 30 seconds.
*
60 Second Start Button Cut Off Delay:
If this option is set to
ENABLE
the
vehicle
can not be started 60
seconds after the ignition key is turned
ON
. Recycling the ignition key
OFF
to
ON
will
reset the time delay for
another 60 seconds.
*
5 Minutes Start Button Cut Off Delay:
If this option is set to
ENABLE
the
vehicle
can not be started 5 minutes
after the ignition key is turned
ON
. Recycling the ignition key
OFF
to
ON
will reset the time de
lay for another 5
minutes.
*
10 Minutes Start Button Cut
off
Delay:
If this option is set to
ENABLE
the
vehicle
can not be started 10
minutes after the ignition key is turned
ON
. Recycling the ignition key
OFF
to
ON
will reset the time delay for
another
10 minutes.
This section explains how to configure the
functions. See section 1.3 for detailed explanation
of each function.
1.
The system must be in
DISARM
mode, and the I
gnition
key must be in the
OFF
position for a minimum
of 3 sec.
2.
Cycle the
I
gnition
key
OFF/ON
3
times, and
keep the ignition key in the
ON
position the 3rd
time
. After
3
sec
the
parking lights will flash 2 times indicating the function setup mode has been activated.
3.
Press
the
ENGINE START
button
OFF/ON
“n”
times
and
o
n the
nth
time hold
the
ENGINE START
button in the
ON
position
for 3 sec.
The parking
light
s
will flash
either 3 times or 1 time
indicat
ing
the
state that the function option has been changed to.
4.
After turning the ignition key to the
OFF
position, the parking lights
will flash 5 times, indicating the
Function Set up Mode has been exited.
5.
To change
another
function
option
repeat steps 1 thru
4
above.
NOTE
: “n” indicates the
number of times the
ENGINE START
button is to be pushed for the respective
Function
Option in
the first column of
TABLE
1
below
.
1.4 PROGRAMMING
FUNCTION SET UP OPTIONS