Garland H28 - User Manual

76 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

Part # 138683 (01/08) Page 1

Users are cautioned that maintenance and repairs must be performed by a Garland authorized service agent

using genuine Garland replacement parts. Garland will have no obligation with respect to any product that has been

improperly installed, adjusted, operated or not maintained in accordance with national and local codes or installation

instructions provided with the product, or any product that has its serial number defaced, obliterated or removed,

or which has been modified or repaired using unauthorized parts or by unauthorized service agents.

For a list of authorized service agents, please refer to the Garland web site at http://www.garland-group.com.

The information contained herein, (including design and parts specifications), may be superseded and is subject

to change without notice.

GARLAND COMMERCIAL INDUSTRIES

185 East South Street

Freeland, Pennsylvania 18224

Phone: (570) 636-1000

Fax: (570) 636-3903

GARLAND COMMERCIAL RANGES, LTD.

1177 Kamato Road, Mississauga, Ontario L4W 1X4

CANADA

Phone: 905-624-0260

Fax: 905-624-5669

Enodis UK LTD.

Swallow eld Way, Hayes, Middlesex UB3 1DQ ENGLAND

Telephone: 081-561-0433

Fax: 081-848-0041

Part # 1382683 (01/08) © 2005 Garland Commercial Industries, Inc.

FOR YOUR SAFETY:

DO NOT STORE OR USE GASOLINE

OR OTHER FLAMMABLE VAPORS OR

LIQUIDS IN THE VICINITY OF

THIS OR ANY OTHER

APPLIANCE

WARNING:

IMPROPER INSTALLATION, ADJUSTMENT,

ALTERATION, SERVICE OR MAINTENANCE

CAN CAUSE PROPERTY DAMAGE, INJURY,

OR DEATH. READ THE INSTALLATION,

OPERATING AND MAINTENANCE

INSTRUCTIONS THOROUGHLY

BEFORE INSTALLING OR

SERVICING THIS EQUIPMENT

PLEASE READ ALL SECTIONS OF THIS MANUAL

AND RETAIN FOR FUTURE REFERENCE.

THIS PRODUCT HAS BEEN CERTIFIED AS

COMMERCIAL COOKING EQUIPMENT AND

MUST BE INSTALLED BY PROFESSIONAL

PERSONNEL AS SPECIFIED.

IN THE COMMONWEALTH OF MASSACHUSETTS

THIS PRODUCT MUST BE INSTALLED BY A

LICENSED PLUMBER OR GAS FITTER. APPROVAL

NUMBER: G-1-07-05-28

For Your Safety:

Post in a prominent location, instructions to be

followed in the event the user smells gas. This

information shall be obtained by consulting

your local gas supplier.

INSTALLATION AND

OPERATION MANUAL

STARFIRE AND STARFIRE SENTRY

SERIES GAS OPERATED RESTAURANT

RANGES, FRYERS & BROILERS

Table of Contents

Other manuals for Garland H28

Specification2 pages

Questions and Answers

L
Lisa ChapmanAug 20, 2025
What to do if my Garland Cookers oven pilot keeps going out?
- B
  Brian TaylorAug 20, 2025
  Several issues could cause the pilot to go out. It could be a faulty thermocouple (check millivolt output), a faulty flame safety device (replace it), the pilot flame might be too small (check pilot flame length), or the thermocouple connection could be loose (check the connection).
A
Angela AveryAug 22, 2025
Why does the burner flame shut off when my Garland H28 oven is at the required temperature?
- O
  oliviasotoAug 22, 2025
  This issue can occur if the thermostat has an incorrect by pass rate. The solution is to replace the thermostat.
M
Megan PriceAug 25, 2025
What causes delayed ignition in Garland Cookers?
- W
  whitekennethAug 25, 2025
  Delayed ignition can occur due to a few reasons: the pilot flame being too small (clean burner), burner ignition ports being blocked (check aeration shutter setting), or incorrect aeration (check millivolt output).
A
Andrew CabreraAug 27, 2025
How to fix a Garland H28 Cookers door that will not stay closed?
- C
  Chloe ClarkAug 27, 2025
  If the door won't stay closed, it could be due to insufficient tension on the springs (adjust the tension), a broken spring (replace it), or a broken hinge link (replace it).
T
Travis GonzalezAug 28, 2025
Why is the millivolt output low on open circuit on my Garland Cookers?
- M
  matthew28Aug 28, 2025
  A low millivolt output on an open circuit can be caused by the pilot flame being too small (adjust pilot flame length) or a defective thermocouple (replace it).
S
Sheri CochranAug 30, 2025
What to do if my Garland Cookers door is not level or low in the center?
- M
  michellehuntAug 30, 2025
  If the door is not level, check the trunnion support. If it's loose, level and tighten it. If it's worn, replace it.
H
hfergusonAug 31, 2025
Why is the burner flame too large on my Garland H28?
- C
  Charles HenryAug 31, 2025
  If the burner flame is too large, it could be due to an incorrect setting pressure or injector. Check the setting pressure or injector.
W
wsmithSep 2, 2025
What causes a noisy motor in Garland Cookers?
- J
  Jason ArmstrongSep 2, 2025
  A noisy motor can be caused by the blower wheel rubbing on the oven baffle (adjust the blower wheel), the blower wheel being loose on the motor shaft (retighten the blower wheel), or a defective motor (replace the motor).
C
cynthia60Sep 4, 2025
What to do if the flame safety valve will not stay open on my Garland H28?
- E
  Eric MaySep 4, 2025
  If the flame safety valve won't stay open, it's likely due to a faulty flame safety device. Replace the flame safety device.
M
Marissa OlsonSep 6, 2025
What to do if my Garland H28 cook/cool down switch is set to “Cook” position, the light is on, but the motor is not working?
- P
  pgonzalesSep 6, 2025
  If the switch is set to 'Cook', the light is on, but the motor isn't working, it could be several things: a defective Cook/Cool Down Switch (replace it), a defective door switch (replace it), faulty wiring (check conditions of wires and all connections), a defective motor (replace the motor), the oven door being open (close the door), or the door switch being out of alignment (align the door switch).

Garland H28 Specifications

General

Model	H28
Width (in)	28
Burners	2
Gas type	Natural Gas or Propane
Material	Stainless Steel
Fuel Type	Gas
Configuration	Range

Related product manuals

Garland Starfire Sentry Series

Garland ST286-E

Preview: Garland Starfire Series

Garland Starfire Series