To Next PageTo Next PageWhat to do if my Garland Cookers oven pilot keeps going out?
Several issues could cause the pilot to go out. It could be a faulty thermocouple (check millivolt output), a faulty flame safety device (replace it), the pilot flame might be too small (check pilot flame length), or the thermocouple connection could be loose (check the connection).
Why does the burner flame shut off when my Garland Cookers oven is at the required temperature?
This issue can occur if the thermostat has an incorrect by pass rate. The solution is to replace the thermostat.
What causes delayed ignition in Garland ST286-E?
Delayed ignition can occur due to a few reasons: the pilot flame being too small (clean burner), burner ignition ports being blocked (check aeration shutter setting), or incorrect aeration (check millivolt output).
How to fix a Garland ST286-E Cookers door that will not stay closed?
If the door won't stay closed, it could be due to insufficient tension on the springs (adjust the tension), a broken spring (replace it), or a broken hinge link (replace it).
Why is the millivolt output low on open circuit on my Garland ST286-E?
A low millivolt output on an open circuit can be caused by the pilot flame being too small (adjust pilot flame length) or a defective thermocouple (replace it).
What to do if my Garland Cookers door is not level or low in the center?
If the door is not level, check the trunnion support. If it's loose, level and tighten it. If it's worn, replace it.
Why is the burner flame too large on my Garland Cookers?
If the burner flame is too large, it could be due to an incorrect setting pressure or injector. Check the setting pressure or injector.
What causes a noisy motor in Garland ST286-E?
A noisy motor can be caused by the blower wheel rubbing on the oven baffle (adjust the blower wheel), the blower wheel being loose on the motor shaft (retighten the blower wheel), or a defective motor (replace the motor).
What to do if the flame safety valve will not stay open on my Garland ST286-E Cookers?
If the flame safety valve won't stay open, it's likely due to a faulty flame safety device. Replace the flame safety device.
What to do if my Garland ST286-E Cookers cook/cool down switch is set to “Cook” position, the light is on, but the motor is not working?
If the switch is set to 'Cook', the light is on, but the motor isn't working, it could be several things: a defective Cook/Cool Down Switch (replace it), a defective door switch (replace it), faulty wiring (check conditions of wires and all connections), a defective motor (replace the motor), the oven door being open (close the door), or the door switch being out of alignment (align the door switch).
Identifies the specific product series covered by the manual.
Warns about chemicals known to cause cancer or reproductive harm.
Covers gas type, pressure checks, and ensuring adequate supply.
Details how to adjust pilot flames for different burner types and safety devices.
Describes how to adjust air shutters for optimal burner flame.
Explains how to adjust and recalibrate the BJWA griddle thermostat.
Lists common oven problems and their possible causes and solutions.
Addresses issues specific to convection ovens, including motor and switch problems.
Lists problems related to burner flames and ignition for models with or without flame supervision.
Covers common issues related to hot tops, griddles, and broilers.
Addresses problems specific to fryers, including millivolt output and ignition issues.
Identifies the specific product series covered by the manual.
Warns about chemicals known to cause cancer or reproductive harm.
Covers gas type, pressure checks, and ensuring adequate supply.
Details how to adjust pilot flames for different burner types and safety devices.
Describes how to adjust air shutters for optimal burner flame.
Explains how to adjust and recalibrate the BJWA griddle thermostat.
Lists common oven problems and their possible causes and solutions.
Addresses issues specific to convection ovens, including motor and switch problems.
Lists problems related to burner flames and ignition for models with or without flame supervision.
Covers common issues related to hot tops, griddles, and broilers.
Addresses problems specific to fryers, including millivolt output and ignition issues.
General
