To Next PageTo Next PageWhat does it mean when my Garland XE24 displays a 'Motor Overcurrent Error'?
A 'Motor Overcurrent Error' on your Garland Grill indicates that the current to the motor exceeds 4.8 amps. This typically happens because the platen movement has encountered mechanical resistance.
Why does my Garland XE24 Grill show a 'Gas Ignition Error'?
A 'Gas Ignition Error' on your Garland Grill means that the ignition feedback signal did not respond after four attempts.
What does 'Platen Down Error' mean on my Garland Grill?
A 'Platen Down Error' on your Garland Grill occurs at the start of a cycle if the platen doesn't reach the lower limit position within 40 seconds.
What does 'Platen Up Error' mean on my Garland XE24 Grill?
A 'Platen Up Error' on your Garland Grill happens at the end of a cycle if the platen fails to reach the upper limit position within 40 seconds.
What does 'Motor Error2' mean on my Garland Grill?
A 'Motor Error2' on your Garland Grill indicates that the platen is in motion but fails to reach the upper or lower limit position within 30 seconds (150 encoder counts).
What does 'Motor Error' mean on my Garland XE24?
A 'Motor Error' on your Garland Grill means that while the platen is moving up or down between limits, it doesn't generate 5 encoder counts in any 1-second interval.
What does 'Lower Switch Error' mean on my Garland XE24 Grill?
A 'Lower Switch Error' on your Garland Grill occurs at the cycle start when the lower limit switch doesn't signal that the platen has reached the lower limit position within 200 seconds.
What does 'COMM Error' mean on my Garland XE24 Grill?
A 'COMM Error' on your Garland Grill indicates a communication failure between the main control and the motor speed controller.
Mandatory safety guidelines for operating the appliance.
Warning regarding improper installation, adjustment, or service.
Overview of the Garland Xpress Grill and its cooking capabilities.
Highlights of the appliance's design and functionalities.
Detailed technical specifications and dimensions for the XE24 model.
Detailed technical specifications and dimensions for the XE36 model.
Crucial safety rules for operating the grill to prevent injury.
Specific warnings to avoid serious personal injury during use.
Mandatory requirements for installing the appliance.
Instructions for proper grounding and electrical connections.
Description of the main power switch and zone indicator lights.
Explanation of the display screen and gap setting controls.
Detailed functions of Power, Program, Temperature, Arrow, Enter, Cancel/Raise, and Black buttons.
Step-by-step guide for installing the release material sheets.
Conditions indicating when a release material sheet needs replacement.
Procedure for performing two-sided cooking cycles.
Procedure for operating the grill in flat grill mode.
How to view current temperatures and menu item settings.
Instructions for entering/exiting standby and initiating clean mode.
Configuration options for platen set, extended time, and start delay.
Procedures for cleaning the grill during operation and daily.
Comprehensive steps for cleaning the grill surfaces and components.
Steps to reset and adjust the platen positions.
Detailed guide for adjusting platens using the gapping tool.
Steps to enter the programming mode and access menu items.
How to set product names and adjust cook times.
Configuration settings for temperature units, gap display, and alarms.
Accessing service mode for tests and diagnostics.
Adjusting upper platen and grill set temperatures.
Modifying cook times and controlling the upper platen.
Setting product names and viewing recovery times.
Accessing system info like part numbers and flash numbers.
Viewing identification numbers for the grill.
Accessing software and download version information.
Configuring temperature units and gap display units.
Adjusting alarm volume and calibrating upper probe.
Calibrating grill probe and setting platen position.
Configuring the instant-on feature for cook cycles.
Setting control type (electric/gas) and enabling extended time.
Configuring grill function (flat/clamshell) and start delay.
Configuring alarm modes and enabling/disabling clean mode.
Changing the SCK address in service mode.
Performing a test on the platen limit switches.
Adjusting the gap setting for cooking platens.
Conditions and requirements for performing calibration.
Detailed instructions for calibrating the grill's probes.
Diagrams showing thermocouple probe locations for XE24 and XE36 models.
Explanation of probe, platen, and heating errors.
Troubleshooting comm, motor over current, and motor errors.
Electrical schematic for the Garland XE24/XE36 models.
Electrical schematic for CE models (400V 50Hz).
Mandatory safety guidelines for operating the appliance.
Warning regarding improper installation, adjustment, or service.
Overview of the Garland Xpress Grill and its cooking capabilities.
Highlights of the appliance's design and functionalities.
Detailed technical specifications and dimensions for the XE24 model.
Detailed technical specifications and dimensions for the XE36 model.
Crucial safety rules for operating the grill to prevent injury.
Specific warnings to avoid serious personal injury during use.
Mandatory requirements for installing the appliance.
Instructions for proper grounding and electrical connections.
Description of the main power switch and zone indicator lights.
Explanation of the display screen and gap setting controls.
Detailed functions of Power, Program, Temperature, Arrow, Enter, Cancel/Raise, and Black buttons.
Step-by-step guide for installing the release material sheets.
Conditions indicating when a release material sheet needs replacement.
Procedure for performing two-sided cooking cycles.
Procedure for operating the grill in flat grill mode.
How to view current temperatures and menu item settings.
Instructions for entering/exiting standby and initiating clean mode.
Configuration options for platen set, extended time, and start delay.
Procedures for cleaning the grill during operation and daily.
Comprehensive steps for cleaning the grill surfaces and components.
Steps to reset and adjust the platen positions.
Detailed guide for adjusting platens using the gapping tool.
Steps to enter the programming mode and access menu items.
How to set product names and adjust cook times.
Configuration settings for temperature units, gap display, and alarms.
Accessing service mode for tests and diagnostics.
Adjusting upper platen and grill set temperatures.
Modifying cook times and controlling the upper platen.
Setting product names and viewing recovery times.
Accessing system info like part numbers and flash numbers.
Viewing identification numbers for the grill.
Accessing software and download version information.
Configuring temperature units and gap display units.
Adjusting alarm volume and calibrating upper probe.
Calibrating grill probe and setting platen position.
Configuring the instant-on feature for cook cycles.
Setting control type (electric/gas) and enabling extended time.
Configuring grill function (flat/clamshell) and start delay.
Configuring alarm modes and enabling/disabling clean mode.
Changing the SCK address in service mode.
Performing a test on the platen limit switches.
Adjusting the gap setting for cooking platens.
Conditions and requirements for performing calibration.
Detailed instructions for calibrating the grill's probes.
Diagrams showing thermocouple probe locations for XE24 and XE36 models.
Explanation of probe, platen, and heating errors.
Troubleshooting comm, motor over current, and motor errors.
Electrical schematic for the Garland XE24/XE36 models.
Electrical schematic for CE models (400V 50Hz).
General
