GE ADTS552F

To Next Page

To Previous Page

DUAL HAND TERMINAL

[EN] English 19 K0553 Revision D

Figure 1-8: ADTS Touch Slave

Main Page

Scope3
Safety3
Pressure3
Toxic Materials3
Marks and Symbols on the Equipment4
Compliance Statements5
Abbreviations11
Glossary14
Conversion Chart16
Unit Conversion16
Table of Contents17
Introduction19
ADTS542F General Arrangemen21
Adts542F21
- Test Set Status Indications22
- Power on and Self Test22
- Aircraft Status22
- ADTS552F General Arrangement23
Adts552F23
ADTS553F General Arrangement24
Adts553F24
ADTS554F General Arrangement25
Adts554F25
- ADTS Touch26
- Status Indicators27
- Dashboard Status Indicators27
- Pressure Mode Selection28
- Measure/Control Mode28
- Pressure/Aeronautical Units Selection28
Dual Hand Terminal29
- ADTS Touch Slave30
- Installation31
- Standard32
- Options32
Packaging32
Environment33
Packing for Storage or Transportation33
- Safety Precautions35
- Important Notice35
- Power Supply35
Returned Goods Procedure35
- External Functional Earth/Ground Terminal36
- Power Supply Connection36
- Fuses36
Pneumatic Pressure Connections37
Positioning the ADTS38
Operation40
Preparation41
Wired Connection43
Power-Up Routine43
- Wireless Connection44
- ADTS Power-Up Self Test Screen44
- ADTS Power-Up Self Test Screen with Bluetooth/Epr44
- Wireless Connection on ADTS542/552F45
- To Establish a Wireless Connection45
- Wireless Connection on ADTS553/554F45
Dashboard47
- Test Sequence48
- Measure Mode Screen - Single Channel49
- Measure Mode49
Pitot Static49
- Measure Mode Screen - Multi Channel50
- Control Mode50
- Control Mode Screen - Single Channel51
- Control Mode Screen - Multi Channel51
- ALT, CAS and Mach52
- Numbered Keypad Screen52
- Nudge Increment/Decrement Factor Selection53
- CAS (CAS1, CAS2 on ADTS554)53
- Mach (MACH1, MACH2 on ADTS554)53
- Qc (Qc1, Qc2 on ADTS554)54
- Altitude Dropback54
- Pt (Pt1, Pt2 on ADTS554)54
- Ps (Ps1, Ps2 on ADTS553/554)54
- Rate Timer Panel - Single Channel55
Rate Timer Mode55
- Rate Timer Panel - Multi Channel56
- To Set the WAIT Period56
- Set Time Panel56
- To Set the “TEST” Period57
- To Start and Stop the Rate Timer57
- Measured Average Rates of Change58
- Settings Menu Overview59
Settings59
- ADTS Settings60
- Intensity60
- Volume60
- Theme60
- Pressure Units61
- Aero Units61
- Altitude Correction61
- PS1-PS2 Differential Limit in 3 Channel Operation61
- Airspeed Mode62
- Temperature Units62
- ADTS Limits62
- Max Aero (ADTS542)63
- ADTS Max (ADTS552F/553F/554F)63
- Max Aero (ADTS552F/553F/554F)64
- Helicopter65
- Fixed Wing65
- ADS Probe66
- Edit Limits67
- Create New Limits67
- Delete Limits68
- Auto Zero68
- Change Supervisor PIN68
- To Turn Auto Zero on and off68
- Configuration69
- Regional Settings69
- Date69
- To Change the Date Setting69
- Bluetooth Autoconnect70
- Area of Use70
- Screen Rotation70
- Language70
Tools71
- Calibration (Calibrate Sensors)72
- To Enter New Correction Values for Ps72
- Calibration (Software Upgrade)73
- ADTS Touch Software Upgrade73
- ADTS Software Upgrade73
- List of Devices73
- Communications Main Screen74
- To View the Status Information for the ADTS Touch or ADTS75
- Save/Recall ADTS Touch Settings76
- Displays a List of Previously Saved Settings76
- ADTS Manuals Screen78
- Customer Documents78
- Go to Ground Main Screen - Single Channel79
Go to Ground79
- Go to Ground Main Screen - Multiple Channel80
- Set Rate Panel81
- Start Go to Ground Action82
- Aircraft Going to Ground - Single Channel82
- Aircraft Going to Ground - Multiple Channel83
- Hold Status During Go to Ground Ramp84
- Aircraft at Ground84
- ADTS Status on Power Failure86
- ADTS Status on Restoration of Power86
- Two Courses of Action Are Possible at this Point86
Manual Venting of the Aircraft Pitot and Static Systems86
- Manual Let-Down ADTS55387
- Manual Let-Down ADTS542F and ADTS552F87
- Manual Let-Down ADTS554F88
- Mutli-Channel Operation89
- Settings Menu to Disable Static Channel89
- Angle of Attack (Smart Probe) Testing89
Multi-Channel Advanced Features89
- Preparation for Testing91
- Aircraft Connections91
Example Basic Aircraft Test Operation Using the ADTS542F91
- Altimeter and Airspeed Indicator Testing92
- Limits Protection Checks92
- Leak Checks93
- Typical Aircraft Instrument Performance Checks93
- End of Testing94
- Setting the EPR - Method 195
Engine Pressure Ratio (EPR)95
- Setting the EPR - Method 296
- EPR Limits97
- Test Sequence Screen99
- Test Sequences Menu100
- Test Procedure Selection Screen100
- Creating Custom Test Sequences101
- Test Sequence Screen Based on Data Field Input102
- Test Sequence Data Fields103
- Saving Finished Test Sequences as CSV Format104
- Saving the Test Sequence File104
- ADTS Touch File Explorer Window104
- How to Use the Pt Only Control Mode106
- Example of Pt Only Control Mode106
Pt Only or Ps Only Control Modes106
Pt Only Control Mode107
Bluetooth108
- Optimum Pairing Procedure109
- Bluetooth Reliable Coverage Area109
- External Bluetooth Antenna111
ADTS TOUCH-ER (Extended Range) Bluetooth111
- Bluetooth Antenna Extension Kit112
- Calibration114
Introduction115
Important Note116
PIN Codes and PIN Protection116
Precision117
Calibration Process117
- Suggested Two-Point Calibration Adjustment Points118
- Calibration Equipment Uncertainty118
- Calibration Requirements ADTS552/553/554F118
- Suggested Calibration Check Points119
- Calibration Check Points119
- Preliminary Operations120
- Calibration Check120
Calibration Description120
- Calibration Adjustment121
- Adjustment Points121
Completion of Sensor Calibration122
- Maintenance123
- Maintenance Chart124
Introduction124
ADTS Touch Battery Pack125
Battery Care and Maintenance125
Maintenance Tasks126
- Replacing the Output Connector O-Ring127
- Replacing a Fuse127
Routine Maintenance127
Downloading Software Updates128
Software Updates128
- Installing Software Updates129
- Software Update Folders129
- To Install Software Updates for the ADTS and ADTS Touch129
- Software Updates-ADTS Touch130
- Downloading ADTS Manuals130
- Enter Name of File to Save131
- Installing ADTS Manuals or Customer Documents131
- Testing and Fault Finding132
Introduction133
Standard Serviceability Test134
- Pressure Leak Check135
- Set-Up135
ADTS Leak Check135
- Vacuum Leak Check136
- Front Panel Four LED Flash Code137
Fault Codes and Error Messages137
Error Codes138
Specification152

Table of Contents

Other manuals for GE ADTS552F

Related product manuals