To Next Page

To Previous Page

GE Multilin C60 Breaker Protection System 5-107

5 SETTINGS 5.4 SYSTEM SETUP

Figure 5–26: EXAMPLE USE OF SOURCES

Y LV D HV AUX

SRC 1 SRC 2 SRC 3

Phase CT M1 F1+F5 None

Ground CT M1 None None

Phase VT M5 None None

Aux VT None None U1

827794A1.CDR

F 5

F 1

DSP Bank

U 1

M 1

M 5

51BF-1 51BF-2

Source 4

87T

51P

UR Relay

Var

Amps

Source 1

Source 3

Volts

Amps

Volts

Amps

Source 2

Default Chapter3
- Table of Contents3
1 Getting Started11
- Important Procedures11
  - Cautions and Warnings11
  - Inspection Procedure12
- Ur Overview13
- Enervista Ur Setup Software15
- Ur Hardware26
- Using the Relay27
2 Product Description31
- Introduction31
- Order Codes39
- Signal Processing47
  - Ur Signal Processing47
- Specifications49
3 Hardware61
- Description61
  - Panel Cutout61
  - Rear Terminal Layout67
- Wiring69
- Direct Input/Output Communications91
4 Human Interfaces109
- Enervista Ur Setup Interface109
- Extended Enervista Ur Setup Features112
- Faceplate Interface121
5 Settings135
- Overview137
- Product Setup144
- System Setup240
- Flexlogic282
- Grouped Elements304
- Control Elements341
- Inputs and Outputs390
- Transducer Inputs and Outputs410
- Records445
- Product Information448
  - Model Information448
  - Firmware Revisions448
7 Commands and449
- Commands449
8 Theory of Operation463
- Fault Locator463
  - Fault Type Determination463
9 Maintenance467
- Modules467
  - Replace a Module467
- Batteries469
  - Replace Battery469
  - Dispose of Battery471
- Uninstall and Clear Files and Data474
- Repairs475
- Storage476
- Disposal477
Parameter Lists479
- Flexanalog Items479
- A.1.1 Flexanalog Items479
- Flexinteger Items491
- A.1.2 Flexinteger Items491
Modbus Communications493
Modbus Rtu Protocol493
- Introduction493
- Physical Layer493
- Data Link Layer493
- B.1.1 Introduction493
- Modbus Rtu Crc-16 Algorithm494
Modbus Function Codes496
- Supported Function Codes496
- Read Actual Values or Settings (Function Code 03/04H496
- Execute Operation (Function Code 05H497
- Store Single Setting (Function Code 06H497
- Store Multiple Settings (Function Code 10H498
- Exception Responses498
- B.3.1 Obtaining Relay Files Via Modbus499
File Transfers500
Memory Mapping501
- Modbus Memory Map501
- Data Formats567
- B.4.2 Data Formats567
Iec 61850603
- Introduction603
- Communication Profiles603
- C.1.1 Introduction603
- Overview604
- C.1.3 File Transfer by Iec 61850604
- Ggio1: Digital Status Values605
- Ggio2: Digital Control Values605
- Ggio3: Digital Status and Analog Values from Goose Data605
- Ggio4: Generic Analog Measured Values605
- C.2.1 Overview605
- Mmxu: Analog Measured Values606
- Protection and Other Logical Nodes606
Server Features and Configuration608
- Buffered/Unbuffered Reporting608
- File Transfer608
- Timestamps and Scanning608
- Logical Device Name608
- Location608
- Logical Node Name Prefixes609
- Connection Timing609
- Non-Iec 61850 Data609
- Communication Software Utilities609
Generic Substation Event Services: Gsse and Goose610
- Overview610
- Gsse Configuration610
- Fixed Goose610
- Configurable Goose610
- C.4.1 Overview610
- Ethernet Mac Address for Gsse/Goose613
- Gsse ID and Goose ID Settings613
Iec 61850 Implementation Via Enervista Ur Setup614
- Overview614
- C.5.1 Overview614
- Configuring Iec 61850 Settings615
- About ICD Files616
- Creating an ICD File with Enervista Ur Setup620
- About Scd Files620
- Importing an Scd File with Enervista Ur Setup623
Acsi Conformance625
- Acsi Basic Conformance Statement625
- Acsi Models Conformance Statement625
- Acsi Services Conformance Statement626
- C.7.1 Logical Nodes Table629
Logical Nodes Table630
Iec 60870-5-103633
- Overview633
- D.1.1 Overview633
- Interoperability Document634
- D.1.3 Interoperability Document634
Iec 60870-5-104636
Overview639
- Interoperability Document639
- E.1.1 Interoperability Document639
- Point List647
- E.1.2 Point List647
Device Profile Document649
- Dnp V3.00 Device Profile649
- F.1.2 Implementation Table652
Dnp Point Lists656
- Binary Input Points656
- Binary and Control Relay Output657
- Counters658
  - F.2.3 Counters658
  - F.2.4 Analog Inputs659
Radius Server Configuration661
Change Notes663
- Revision History663
- H.1.1 Revision History663
- Changes to the C60 Manual664
Abbreviations668
- Standard Abbreviations668
  - H.2.1 Standard Abbreviations668
  - H.3.1 Ge Multilin Warranty671

Questions and Answers:

Need help?

Do you have a question about the GE C60 and is the answer not in the manual?

GE C60 Specifications

General

Brand	GE
Model	C60
Category	Relays
Language	English

Related product manuals

GE C60 User Manual

Table of Contents

Questions and Answers:

GE C60 Specifications

Related product manuals