GE C60

682 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

GE Multilin C60 Breaker Protection System 7-3

7 COMMANDS AND TARGETS 7.1 COMMANDS

7

The timescale of the entered time is local time, including daylight savings time where and when applicable.

Table of Contents

Default Chapter3
- Table of Contents3
1 Getting Started11
- Important Procedures11
  - Cautions and Warnings11
  - Inspection Procedure12
- Ur Overview13
- Enervista Ur Setup Software15
- Ur Hardware26
- Using the Relay27
2 Product Description31
- Introduction31
- Order Codes39
- Signal Processing47
  - Ur Signal Processing47
- Specifications49
3 Hardware61
- Description61
  - Panel Cutout61
  - Rear Terminal Layout67
- Wiring69
- Direct Input/Output Communications91
4 Human Interfaces109
- Enervista Ur Setup Interface109
- Extended Enervista Ur Setup Features112
- Faceplate Interface121
5 Settings135
- Overview137
- Product Setup144
- System Setup240
- Flexlogic282
- Grouped Elements304
- Control Elements341
- Inputs and Outputs390
- Transducer Inputs and Outputs410
- Records445
- Product Information448
  - Model Information448
  - Firmware Revisions448
7 Commands and449
- Commands449
8 Theory of Operation463
- Fault Locator463
  - Fault Type Determination463
9 Maintenance467
- Modules467
  - Replace a Module467
- Batteries469
  - Replace Battery469
  - Dispose of Battery471
- Uninstall and Clear Files and Data474
- Repairs475
- Storage476
- Disposal477
Parameter Lists479
- Flexanalog Items479
- A.1.1 Flexanalog Items479
- Flexinteger Items491
- A.1.2 Flexinteger Items491
Modbus Communications493
Modbus Rtu Protocol493
- Introduction493
- Physical Layer493
- Data Link Layer493
- B.1.1 Introduction493
- Modbus Rtu Crc-16 Algorithm494
Modbus Function Codes496
- Supported Function Codes496
- Read Actual Values or Settings (Function Code 03/04H496
- Execute Operation (Function Code 05H497
- Store Single Setting (Function Code 06H497
- Store Multiple Settings (Function Code 10H498
- Exception Responses498
- B.3.1 Obtaining Relay Files Via Modbus499
File Transfers500
Memory Mapping501
- Modbus Memory Map501
- Data Formats567
- B.4.2 Data Formats567
Iec 61850603
- Introduction603
- Communication Profiles603
- C.1.1 Introduction603
- Overview604
- C.1.3 File Transfer by Iec 61850604
- Ggio1: Digital Status Values605
- Ggio2: Digital Control Values605
- Ggio3: Digital Status and Analog Values from Goose Data605
- Ggio4: Generic Analog Measured Values605
- C.2.1 Overview605
- Mmxu: Analog Measured Values606
- Protection and Other Logical Nodes606
Server Features and Configuration608
- Buffered/Unbuffered Reporting608
- File Transfer608
- Timestamps and Scanning608
- Logical Device Name608
- Location608
- Logical Node Name Prefixes609
- Connection Timing609
- Non-Iec 61850 Data609
- Communication Software Utilities609
Generic Substation Event Services: Gsse and Goose610
- Overview610
- Gsse Configuration610
- Fixed Goose610
- Configurable Goose610
- C.4.1 Overview610
- Ethernet Mac Address for Gsse/Goose613
- Gsse ID and Goose ID Settings613
Iec 61850 Implementation Via Enervista Ur Setup614
- Overview614
- C.5.1 Overview614
- Configuring Iec 61850 Settings615
- About ICD Files616
- Creating an ICD File with Enervista Ur Setup620
- About Scd Files620
- Importing an Scd File with Enervista Ur Setup623
Acsi Conformance625
- Acsi Basic Conformance Statement625
- Acsi Models Conformance Statement625
- Acsi Services Conformance Statement626
- C.7.1 Logical Nodes Table629
Logical Nodes Table630
Iec 60870-5-103633
- Overview633
- D.1.1 Overview633
- Interoperability Document634
- D.1.3 Interoperability Document634
Iec 60870-5-104636
Overview639
- Interoperability Document639
- E.1.1 Interoperability Document639
- Point List647
- E.1.2 Point List647
Device Profile Document649
- Dnp V3.00 Device Profile649
- F.1.2 Implementation Table652
Dnp Point Lists656
- Binary Input Points656
- Binary and Control Relay Output657
- Counters658
  - F.2.3 Counters658
  - F.2.4 Analog Inputs659
Radius Server Configuration661
Change Notes663
- Revision History663
- H.1.1 Revision History663
- Changes to the C60 Manual664
Abbreviations668
- Standard Abbreviations668
  - H.2.1 Standard Abbreviations668
  - H.3.1 Ge Multilin Warranty671

Related product manuals

Preview: GE 469

Preview: GE 369

Preview: GE 750

Preview: GE 345

Preview: GE B90

Preview: GE T60

Preview: GE 735

Preview: GE P642

Preview: GE KVGC 202

Preview: GE UR series